FAQ
(24) Results were found. Showing 1-10.
Is There a Banana Jack Adaptor for the 700929 Isolated Probe?
Yes, to provide safety and isolation to sensitive test points please use the following banana jack adaptors: M1223WP-A Push-on Safety Male Banana Plug M1223WQ-A Banana Plug Reference Lead We also provide various additio...
item: 98 | http://tmi.yokogawa.com/de/service-support/faqs/98/
Where can I Find Documentation Describing the *.WDF File Format?
Unfortunately, we do not have an instruction manual describing the*.WDF file format structure like we did for the *.WVF files. However, we do provide a list of support options which will contain more details and explana...
item: 1042 | http://tmi.yokogawa.com/de/service-support/faqs/1042/
What is the Replacement Model for the 700952 150 MHz Passive Probe?
We recommend the 700960 200 MHz Passive Probe as the replacement for the 700952 150 MHz Passive Probe. The probe specification for the 700960 probe is the closest match to the 700952 probe, when using the DL1200. The D...
item: 1115 | http://tmi.yokogawa.com/de/service-support/faqs/1115/
What is Decimation and How do I use Decimation in Xviewer?
Decimation is a technique used to reduce the total number of samples. You can use Xviewer to perform decimation on your waveform data files that have the WDF/WVF/ASCII CSV extension format. Decimation reduces the total n...
item: 1029 | http://tmi.yokogawa.com/de/service-support/faqs/1029/
What is the Measured Propagation Delay for the PB500 500 MHz Passive Probe (701943)?
The measured propagation delay for the PB500 500 MHz Passive Probe (701943) is approximately 8.2 ns. A simple way of measuring the propagation delay, using the DL9000, is to measure the delay between two channels usin...
item: 1109 | http://tmi.yokogawa.com/de/service-support/faqs/1109/
If I Break a Passive Probe Such as the 700998 Within One Year of Purchase, is it Covered by a Warranty?
Because of their relative low cost, passive probes are classified as consumables and as such, are not covered by a warranty. More expensive probes such as the FET Probe and the Current Probe are covered by a warranty. ...
item: 100 | http://tmi.yokogawa.com/de/service-support/faqs/100/
What is the temperature range of the 700929?
What is the temperature range of the 700929? The operation temperature for the 700929 is from 5 degree C to 40 degree C. (It is same range for DL850/DL750 mainframe.)...
item: 1356 | http://tmi.yokogawa.com/de/service-support/faqs/1356/
What is the Temperature/Humidity Range of the 700929 Isolated Probe Under Standard Operating Environment?
The temperature range of the 700929 Isolated Probe is from 41°F - 104°F (5°C - 40°C). It is the same as the 701947 isolated probe. ...
item: 666 | http://tmi.yokogawa.com/de/service-support/faqs/666/
Can I use the 700929 Isolated Probe for Non-Isolated Modues Such as the 701255 Voltage Module?
Yes, you can use the 700929 isolated probe with non-isolated input modules. ...
item: 681 | http://tmi.yokogawa.com/de/service-support/faqs/681/
Can I buy a ground clip for my 700929?
Can I buy a ground clip for my new-style 700929? Two part numbers required for new-style probe: NEW STYLE features/requires two pieces: ground ref clip and safety plug-on clip. B9940WX Clip, plug-on, safety,...
item: 1357 | http://tmi.yokogawa.com/de/service-support/faqs/1357/
