KNOWLEDGEBASE
(35) Results were found. Showing 21-30.
How do I Retrieve Data From the Instrument Only When it is Updated Using IEEE488.2 Commands?
You can use the "STATUS:ESSR?" command to access the extended event register and determine whether the data was updated. You can judge the data update status by referencing bit 0 (UPD) of this register. However to do so,...
item: 1249 | http://tmi.yokogawa.com/sg/service-support/faqs/1249/
What Type of Network Printer can the WT1600 Connect to Via Ethernet?
The WT1600 can support printers that have the following commands. ESC-P ESC-P2 (for printers that support ESC/P raster commands) BJ PCL5 LIPS3 Post Script Before attempting to connect a Network Printer to the WT1600, p...
item: 911 | http://tmi.yokogawa.com/sg/service-support/faqs/911/
Why are the Measured Values for VAR and ΣVAR Unstable?
Check the Synch Source and Frequency Filter settings When a single-phase signal being measured fluctuates around power factor of 1.Slight fluctuations in the measured values of voltage, current, and power can cause a la...
item: 1268 | http://tmi.yokogawa.com/sg/service-support/faqs/1268/
Unstable Measured Values of Efficiency When Measuring at I/O Efficiency From Input Power ΣA and Output Power ΣB to and From the Instrument
The measurement intervals of the measured I/O data must overlap exactly. Check the sync source setting. For example, route the input to a three-phase device under measurement to input elements 1-3 on the power meter, an...
item: 1257 | http://tmi.yokogawa.com/sg/service-support/faqs/1257/
Can I use the Store Function to Record Waveform Data on the WT1800?
THE WT1800 and WT500 STORE function can only be used to record NUMERIC data. The WT1600 and WT3000 STORE function can be used to record both NUMERIC and WAVEFORM data. ...
item: 915 | http://tmi.yokogawa.com/sg/service-support/faqs/915/
Product Tutorials for WT & PZ Series Digital Power Meters & Analyzers
The following product tutorial guides have been created for the WT and PZ Series Power Meter and Analyzer instruments and are available for download. Each tutorial contains quick and easy steps to help you get started ...
item: 1121 | http://tmi.yokogawa.com/sg/service-support/faqs/1121/
Why Doesn't the Voltage, Current, Power Values Measured on Power Meter A Match Those From Power Meter B?
Check for differences in the specifications or features of the instruments. For values that do not match when inputting a 50/60 sine wave Check whether the value is within the specifications (error) of each power meter...
item: 1256 | http://tmi.yokogawa.com/sg/service-support/faqs/1256/
Why are the Measured Values for Voltage, Current, and Power Unstable?
Check the "Sync Source" and zero cross filter (frequency filter) settings. For the WT3000, "Sync Source" setting is irrelevant if the data update rate is 250 ms, 500 ms, 1 s, or 2 s. Sync Source SettingIn principle, if t...
item: 1255 | http://tmi.yokogawa.com/sg/service-support/faqs/1255/
Can the WT1600 Display the Average Power Value During Integration?
Yes, by using the User-Defined Function feature, the WT1600 can display the average power value during integration. Enter the following equation to calculate the average power for Element 1: W...
item: 664 | http://tmi.yokogawa.com/sg/service-support/faqs/664/
Why Doesn't the Power, Power Factor, and Phase Angle of Each Input Element Match When Measuring Balanced a Three-Phase Load?
In the case of three-phase three-wire, or 3V3A wiring, the power, power factor, and phase angle of each input element do not match because it is the line to line voltage that is measured. Please download and refer to...
item: 1259 | http://tmi.yokogawa.com/sg/service-support/faqs/1259/
