技术与服务热线:400 820 0372

中国 CN  

用于WT500/WT1600/WT1800/WT1800E/WT3000/WT3000E 的WT文件阅读器

Description

This software allows you to display data saved in WT500/WT1800/WT1800E/WT3000/WT3000E on your PC and change it to .csv format.

System Requirements

PCA PC with a 80486DX2 CPU or later (Pentium or later recommended), and 8 MB or more of memory.

CPU
Premium4 1.5 GHz or higher (recommended)

Memory
1 GB or more (recommended)

Hard Disk
500 MB or more of free space

OS
Microsoft Windows XP, Windows Vista, or Windows 7.(All English versions)

Communication Port

GP-IB
NI (National Instruments) AT-GPIB, PCI-GPIB, PCI-GPIB+, PCMCIA-GPIB, PCMCIA-GPIB+, or PCIe-GPIB with driver NI-488.2 version 1.60 or later (however, version 2.3 is not supported).

RS-232
An available COM port on the PC

Ethernet
10BASE-T or 100BASE-TX compatible Ethernet port

USB
A USB Rev. 1.1 or later USB port

Display

1024 × 768 pixels or higher

Connecting the WT Series Instrument to a PC

GP-IB Interface to prevent electric shock, turn the power to the instrument OFF when connecting it to the PC. Connect a GP-IB cable from the GP-IB connector on the rear panel of the WT series instrument to the corresponding connector on the PC.

  • Setting the Address
    Set the GP-IB address according to the procedure given in the user's manual that came with the WT series instrument. For details about the GP-IB interface, refer to the information about the communications functions included in the user's manual.
  • RS-232C Interface
    To prevent electric shock, turn the power to the PC OFF when connecting the instrument to it. Connect an RS-232 cable from the RS-232 connector on the rear panel of the WT series instrument to the serial port of the PC.
  • Parameter settings
    Follow the procedure given in the user's manual of the WT series instrument to enter the following parameter settings. (Normally, operation can begin using the factory default settings.)
    Handshaking: select a method from 0 to 7.
    Data format: select a format from 0 to 3.
    Baud rate: select 75, 150, 300, 600, 1200, 2400, 4800, or 9600.
    Terminator: select CR+LF, CR, or LF.
    For details about the RS-232 interface, refer to the user's manual that came with the WT series instrument.

Installation

Before Installation

  • Backing up the program files
    Backup the program files you downloaded to a memory media like CF card or USB flash.

Installation

All four downloadable program files are self-extracting executables which, when double-clicked, create new files and folders on your hard drive. Two of those four programs require no further installation, but the other two create an additional Setup.exe file which must be executed to complete the installation.
Turn ON the PC and start Windows. Create a new folder on your hard disk with a name of your choice, and download the free software into the folder. Double-click the file necessary for your WT series model, then click OK in the dialog box. A new folder, YOKOGAWA, will be created on drive C and files will be extracted to it. Specify any changes you wish to make to the destination folder.

When the extraction is finished, check to see if the program executable file was created.
If so, installation is complete. If the Setup.exe file (rather than executable files) was created you will need to perform a few more steps to complete the installation. Double-click the Setup.exe file, and follow the on-screen instructions.

Creating Icons for the WT Free Software

After the program has been fully installed, you can use Explorer or the My Computer browser to create a shortcut to the program. Locate the executable file, right-click its icon, and select Create Shortcut from the shortcut menu. Running/Exiting the Software.

  • Running the software
    Double-click the program executable file or its shortcut to run the software. Or, if the program was installed using a Setup.exe file, select Start > Programs > Yokogawa, then the name of the program you wish to run.
  • Exiting the software
    Select File > Exit, or Close the program window.

Download

 

Please read Software Agreement carefully before downloading.

 

Version 2.23
Release Date Feb 21, 2017
File Name wtfilereader223e.zip 4.0 MB

  

Type Software

 

* 软件协议
  • 本软件的产权、专利、知识产权和其他所有权利均归横河计测株式会社所有。
  • 在任何情况下,不得转存、逆向编辑、逆向编译、反向工程或任何其他更改或修改。
  • 本软件免费提供,但不对任何瑕疵做任何无限制的保证。
  • 此外,横河不接受关于修复瑕疵或有关本软件问题的质询。
  • 由于软件性能和功能的持续改进,本软件的内容如有变更,恕不另行通知。
  • 对于下载或安装本软件过程中可能出现的任何问题,横河将不承担任何责任。
  • 使用横河网站,用户需自己承担风险。
  • 对于使用上述内容所造成的任何损害,参与横河网站内容创建或分发的各方将不承担任何责任。

下载软件即表明接受本 软件协议

相关产品和解决方案

功率分析仪 WT500

中等量程的WT500小巧且便于使用。使用其彩色TFT显示器可以观测数值和波形测量。提供1到3个输入单元,基本功率精度为0.1%,带宽为100kHz。

高性能功率分析仪 WT1800E系列

精度 – 在同类功率分析仪器中, WT1800E能保证功率精度达到“ 读数的0.05% + 量程的0.05%” , 它可以执行多达500次谐波分析(50/60Hz基波频率)。

可靠 – 测量需要重复执行并需要追求准确性。WT1800E稳定性极高, 无论现在还是将来, 都可以确保完成精准的测量。

灵活 – WT1800E不但拥有最多6输入通道、 宽量程显示和分析功能, 还可以和电脑相连接,能在功率效率和谐波分析领域为客户提供广泛的测量解决方案。

高性能功率分析仪 WT1800系列

高端WT1800是WT1600的升级产品,可应用于从节能到高负载应用在内的各种应用领域。WT1800拥有6单元输入能力,可提供最大的灵活性和5MHz带宽下0.1%的基本功率精度。

高精度功率分析仪 WT3000

WT3000高精度功率分析仪提供最高精度的测量。此产品已成为行业标准,用于变频器、电机驱动器、照明系统和电子镇流器、UPS系统、飞机电力系统、变压器测试和其它电力转换设备的研发。WT3000的基本功率精度达0.02%,带宽为1MHz。

高精度功率分析仪 WT3000E

目前光伏逆变器等设备的整体工作效率已达到90%至96%。要进一步提高效率,即使是几个小数点,对制造商来说也是件极具挑战且至关重要的事情。WT3000E作为全球最精确的功率分析仪,所提供的高精度水平可以真正验证效率上的细微改进。如今,在电机与驱动器、半导体、照明以及家用电器等工业和应用领域的研发工程师们,将拥有一款具备更高精度和稳定性的增强型功率测量工具。

返回顶部
WeChat QR Code
微信扫一扫
获得更多专业服务