Brazil BR   

Clamp-on Tester CL150 (ACA, ACV, DCV, OHM, 2000A)

Imagem do produto em destaque

Digital Clamp Meter

  • AC current measurement with current ranges up to 2000A
  • AC/DC voltage and resistance measurements
  • 54mm in diameter of measurable conductor
  • Mean value display
  • DC output function
  • Data hold function
  • Sleep function
  • Approved for conformity to safety standards EN61010-1,
  • EN61010-2-031, EN61010-2-032 (CAT. m 600 V, CAT. II1000 V)
Solicite um orçamento
Suporte Técnico
Brochuras
Manual de instruções
Display (LCD, Digital Counts) 3999
AC Current Accuracy (400A Reference) 1.0+3(50/60Hz)
2.0+3(40~1kHz)
AC Current Accuracy (2000A Reference, 0~1500A) 1.0+3(50/60Hz)
3.0+3(40~1kHz)
AC Voltage Accuracy (40/ 400V/ 750V Reference) 1.0+2(50/60Hz)
1.5+3(40~1kHz)
DC Voltage Accuracy (40/ 400V/ 1000V Reference) 1.0+2
Resistance Accuracy (400/ 4k/ 40k/ 400kΩ reference) 1.5+2, Beeps at below 50± 35Ω (continuity check)
DC Output Accuracy (400A, 0~400mV Reference) .5۫% rdg ± 0.5mV (50/60Hz)
.5% rdg ± 0.5mV (40~1kHz)
Method of detection Mean Value
Response Time Approx. 2 seconds
Range Switching Manual-range (on AC current range) / Auto-range (on AC voltage range, resistance range)
Data hold On all range
Operating temperature and humidity 0-40°C, 85% RH or less (no condensation)
Influence of external magnetic field 1A or less at 400A/m
Influence of conductor position ± (2% rdg + 3dgt) or less
Safety Standard Conforms EN 61010-1, EN61010-2-031, EN61010-2-032
Circuit voltage 1000Vrms or less
Withstanding voltage 5.55kV AC for one minute
Power Supply R6P(SUM-3)x2 or LR6x2
Battery Life1 150 hours
Consumed current Approx. 5mA
Sleep Function Automatically powered down in about 10 minutes after the last switch operation
Diameter of measurable conductor 54mm at maximum
Dimensions Approx. 105(W) x 247(H) x 49(D)mm
Weight (Approx.) 470g
Accessories Clamp Adapter (Model 99025), Output Cable for Terminal Screw (Model 91019), Carrying Case (Model 93034), Output Plug (Model 98012), Test Lead (Model 98011), User's manual (IM CL150), batteries
Order Notes Each item selected MUST be ordered as a separate line item.
Product Notes All Clamp-on Meters include Test Leads (where applicable) and a carrying case.

1 Approximate, continuous

AC Current Range 400/2000A
AC Current Resolution 0.1A
AC Current Frequency characteristics 40~1kHz
AC Current Method of detection Mean Value
AC Voltage Measurement O
DC Voltage Measurement O
Continuity Check Measurement O
Frequency Measurement -
Temperature Measurement -
Recorder output Function O
Waveform monitor output Function -
Data hold Function O
Auto hold Function -
Peak Hold Function O
Maximum value memory Function -
Mean value display Function -
Filter Function -
Range Hold Function O (current range)
Auto ZERO Adjust Function -
Auto power-off Function O Sleep function (power-down)

How To Use Digital Clamp Meter CL150

AC Current Measurement: 

  • Set the Function Selector switch to the " 400A" or " 2000A" position. "AC" should be shown on the upper left corner of the display.
  • Press the open/close lever to open the transformer jaws and clamp them onto the conductor under test, then take the reading on the display. The most accurate reading will be obtained by keeping the conductor at the center of the transformer jaws.

DC Voltage Measurement: 

  • Set the Function Selector switch to the " V " position. "DC" should be shown on the upper left corner of the display.
  • Slide the terminal cover to the left to disclose the Hi and Lo terminals. Plug the red test lead into the Hi terminal and the black test lead into Lo terminal.
  • Connect the tip of the red and black test leads to the positive (+) and negative (-) sides of the circuit under test respectively. Take the reading on the display.

AC Voltage Measurement: 

  • Set the Function Selector switch to the " V " position. "AC" should be shown on the upper left corner of the display.
  • Slide the terminal cover to the left to disclose the Hi and Lo terminals. Plug the red test lead into the Hi terminal and the black test lead into Lo terminal.
  • Connect the tip of the test leads to the circuit under test respectively. Take the reading on the display.
Brochuras
Manual de instruções
Dimensões

Procurando mais informações sobre nossas pessoas, tecnologia e soluções?


Contate-nos

Precision Making

Topo