Others

The carrying case can hold the source signal and measurement lead cables, terminal adapter, four spare batteries, fuses, AC adapter, and user’s manual.

Lead cables for source/measurement, terminal adapter, 6 spare batteries, fuse, AC adapter and Instruction Manual can be stored.

For carrying the CA450, the test leads, and the lead cables

Carrying case with hanger strap and large size case

This carrying case is to be used with the CA300 series volt calibrators and lead cables.

Three pockets are provided for storing accessories and the user’s manual.

Three pockets are provided for storing accessories and the user’s manual.

Three pockets are provided for storing accessories and the user’s manual.

Main baby and accessoryhousing

Soft Case for Accessories

Case for the 91051 (91051, 91052, and instruction manual)

Case for the 91056/91061 (91056, 91057, 91061, 91062, and instruction manual)

CW500 and Clamp-on probe can be contained

Carry your Scopecorder with this carrying case.

With strap and accessory storage case.

Case with magnet

Lead cables, RJ sensor, etc. can be stored.

For DLM4000 series

For DL850/E series

Can connect to –P1 or –P2, input and output port are Rc1/8” female thread

Can connect to –P1 or –P2, input and output port are 1/8” NPT female thread

For DL950,DL350

250 Ω ±0.1%, 0.3 W, ±25 ppm/ ̊C

100 Ω ±0.1%, 0.3 W, ±25 ppm/ ̊C

10 Ω ±0.1%, 0.3 W, ±25 ppm/ ̊C

Shunt resistor boxes for WT1800E /PD option.

Used for terminating (attaching) a single wire or test lead.

Used for terminating (attaching) a single wire or test lead.

K (Yellow) /E (Violet) /J (Black) /T (Blue)

A set of separate red and black clips (for 2 m long wires).

  • ScopeCorder Accessories for DL850 series, DL750/DL750P, SL1000 & SL1400
  • 701955 NDIS Bridge Head, Bridge resistance: 120Ω , 5m NDIS cable included
  • 701956 NDIS Bridge Head, Bridge resistance: 350Ω , 5m NDIS cable included
  • 701957 and 701958 D-SUB Bridge Head
  • Shunt calibration
  • 5m DSUB cable included
  • Bridge resistance:  120Ω 
  • Bridge resistance:  350Ω 

for DL350, AQ7280 and MT300

Battery Pack

Battery pack cover for the 739883 Batery pack.

440 mA/1000 V 10 A cut off 1 piece

For CA71: fuse 1 piece

RJ (Reference Junction)

For reference junction compensation sensor. Pt100, 1.95 m

For reference junction compensation.

The application software can use only the measurement function.
(Logging function only)

USB adapter, USB cable and software

For protection of the main unit.

2 GB SD Memory Card

Used to hang the main unit on wall with rubber boot.

For hanging the main body during measurement

250 Ω resister, terminal adapter and leads

Magnet hook (Maximum weight 1.5 kg)

Used to connect an oscilloscope having a 1M-ohm input to a probe with a 50-ohm output. It is required when using the 701920 and 701922 probes with the DL1600 series.

Set contains one black and one red clip
1000 Vrms-CAT II
2 pieces (red and black) in 1 set 
Connected to the 758933, 758917, or 701901
Length: 0.3m
Applicable for DL750/DL750P, SL1000, SL1400

  • 701936 Deskew Correction Signal Source
  • Improve switching-loss measurements by deskewing
  • Accommodates both clamp-on current probes and through-type ‘CT' Current Transformers

Connected to the 700929, 701947
Maximum input voltage: 1,000V (DC + ACpeak)
Length: 0.26m/0.3m/0.4m
Applicable for DL750/DL750P, SL1000, SL1400

Set contains one black and one red clip.
1000 Vrms-CAT II.

For 720220 input terminal, one (1) piece

Screws for B8200JQ, D-SUB connector

10 Ω/0.25 W (×4)

A clip set designed for the 700988, 700960 and 701940 probes.

  • B9852ES Logic Probe IC Pin Clips
  • Attach to tips of logic probe (701988 or 701989) or mini-clips (B9852CR)
  • Clip contiguous 0.5-mm pitch terminals
  • 10 clips included
  • Quality thermal printer paper for DL750P and the SL1400.
  • Paper width: 210 mm (A4 size)
  • Paper length: 20 m
  • Order Qty: 6 (1set)

Printer Paper Roll
Thermal paper (10m) for WT1600, WT 1800, WT3000, & WT3000E - 1 roll

Quality paper for the DLM2000 /DLM4000 /DL850 /DL6000 /DL9000 and DL750

Battery cover for MT300

Soft Carrying Case

Soft Carrying Case

Shoulder Belt

Battery pack (Spare)

For AQ4280A/AQ4280B/AQ4280C

For AQ2170 /AQ2170H /AQ2180 /AQ2180H /AQ4280A /AQ4280B /AQ4280C

For AQ2170/AQ2170H

For AQ2180 /AQ2180H /AQ4280A /AQ4280B /AQ4280C

For AQ2170/AQ2170H

For AQ2180 /AQ2180H /AQ4280A /AQ4280B /AQ4280C

Used by attaching to the main body.

1000 Vrms CAT III, 1 set each of red and black

Dust protection cap for LC connector

Dust protection cap for MU connector

Light shielding cap for FC connector

Light shielding cap for SC connector

K (yellow)/ E (violet)/ J (black)/ T (blue)/ R•S (green)/ B•U (white)/ G (red, green)/ N (orange)

Looking for more information on our people, technology and solutions?


Contact Us

Precision Making

Top