The carrying case can hold the source signal and measurement lead cables, terminal adapter, four spare batteries, fuses, AC adapter, and user’s manual.
Lead cables for source/measurement, terminal adapter, 6 spare batteries, fuse, AC adapter and Instruction Manual can be stored.
This carrying case is to be used with the CA300 series volt calibrators and lead cables.
Three pockets are provided for storing accessories and the user’s manual.
Three pockets are provided for storing accessories and the user’s manual.
Three pockets are provided for storing accessories and the user’s manual.
Case for the 91056/91061 (91056, 91057, 91061, 91062, and instruction manual)
K (Yellow) /E (Violet) /J (Black) /T (Blue) /R,S (Green) /B,U (White) /G (Red/Green) /D (Red/White) /C (Red) /N (Orange)
701955 NDIS Bridge Head, Bridge resistance: 120Ω , 5m NDIS cable included
701956 NDIS Bridge Head, Bridge resistance: 350Ω , 5m NDIS cable included
701957 DSUB Bridge Head with Shunt calibration
Bridge resistance: 120Ω , 5m DSUB cable included
701958 DSUB Bridge Head with Shunt calibration
Bridge resistance: 350Ω , 5m DSUB cable included
The application software can use only the measurement function.
(Logging function only)
USB adapter, USB cable and software
Used to connect an oscilloscope having a 1M-ohm input to a probe with a 50-ohm output. It is required when using the 701920 and 701922 probes with the DL1600 series.
Set contains one black and one red clip
1000 Vrms-CAT II
2 pieces (red and black) in 1 set
Connected to the 758933, 758917, or 701901
Length: 0.3m
Applicable for DL750/DL750P, SL1000, SL1400
Improve switching-loss measurements by eliminating skew. The 701936 Deskew Correction Signal Source accommodates both clamp-on current probes and through-type ‘CT' Current Transformers.
Connected to the 700929, 701947
Maximum input voltage: 1,000V (DC + ACpeak)
Length: 0.26m/0.3m/0.4m
Applicable for DL750/DL750P, SL1000, SL1400
Set contains one black and one red clip.
1000 Vrms-CAT II.
This DC block can be used to remove the DC component from an incoming signal. Use this block if you want to remove bias voltage from reaching the PBL5000 probe.
(2 pcs./unit. order qty 1 unit)
The auxiliary earthing nets are used to improve the earthing conditions of the earth spikes. For example, on soft ground such as hard places such as concrete, etc. where the spikes cannot be driven.
Attached to the tips of logic probe (701988 or 701989) or mini-clips (B9852CR), the IC clips can be used to clip contiguous 0.5-mm pitch terminals. A total of 10 clips are included.
The B9852HF contains the following eleven(11) kinds of accessories: Insulation cap, IC cap, BNC adapter, Rigid tip, Spring tip (Ø: 0.80 mm), Spring tip (Ø: 0.38 mm), Ground spring, Adjustment tool, Pincher tip, Standard ground lead, Color coding rings. PBL5000.
Quality paper for the DL750P and the SL1400.
Paper width: 210 mm (A4 size)
Paper length: 20 m
Order Qty: 6 (1set)
Printer Paper Roll
Thermal paper (10m) for WT1600, WT 1800, WT3000, & WT3000E - 1 roll
Quality paper for the DLM6000/DL9700/DL9500/DL1700(E)/DL1600/DL1500 and DL7400