Others

The carrying case can hold the source signal and measurement lead cables, terminal adapter, four spare batteries, fuses, AC adapter, and user’s manual.

Lead cables for source/measurement, terminal adapter, 6 spare batteries, fuse, AC adapter and Instruction Manual can be stored.

For carrying the CA450, the test leads, and the lead cables

Carrying case with hanger strap and large size case

This carrying case is to be used with the CA300 series volt calibrators and lead cables.

Three pockets are provided for storing accessories and the user’s manual.

Three pockets are provided for storing accessories and the user’s manual.

Three pockets are provided for storing accessories and the user’s manual.

Main baby and accessoryhousing

Soft Case for Accessories

Case for the 91051 (91051, 91052, and instruction manual)

Case for the 91056/91061 (91056, 91057, 91061, 91062, and instruction manual)

CW500 and Clamp-on probe can be contained

Carry your Scopecorder with this carrying case.

With strap and accessory storage case.

Case with magnet

Lead cables, RJ sensor, etc. can be stored.

For DLM4000 series

For DL850/E series

Can connect to –P1 or –P2, input and output port are Rc1/8” female thread

Can connect to –P1 or –P2, input and output port are 1/8” NPT female thread

For DL350

250 Ω ±0.1%, 0.3 W, ±25 ppm/ ̊C

100 Ω ±0.1%, 0.3 W, ±25 ppm/ ̊C

10 Ω ±0.1%, 0.3 W, ±25 ppm/ ̊C

Shunt resistor boxes for WT1800E /PD option.

Hand pump (91051), connector set (91052), case (93052)

Hand pump (91056), connector set (91057), case (93053)

Hand pump (91061), connector set (91062), case (93053)

Used for terminating (attaching) a single wire or test lead.

Used for terminating (attaching) a single wire or test lead.

1000 Vrms CAT III black

1000 Vrms CAT III red

K (Yellow) /E (Violet) /J (Black) /T (Blue) /R,S (Green) /B,U (White) /G (Red/Green) /D (Red/White) /C (Red) /N (Orange)

K (Yellow) /E (Violet) /J (Black) /T (Blue)

A set of separate red and black clips (for 2 m long wires).

701955 NDIS Bridge Head, Bridge resistance: 120Ω , 5m NDIS cable included
701956 NDIS Bridge Head, Bridge resistance: 350Ω , 5m NDIS cable included

701957 DSUB Bridge Head with Shunt calibration
Bridge resistance:  120Ω , 5m DSUB cable included
701958 DSUB Bridge Head with Shunt calibration
Bridge resistance:  350Ω , 5m DSUB cable included

for DL350, AQ7280 and MT300

NiMH battery Dedicated.

Battery pack cover for the 739883 Batery pack.

440 mA/1000 V 10 A cut off 1 piece

For CA71: fuse 1 piece

For the CA320: RJ (Reference Junction)

For reference junction compensation sensor. Pt100, 1.95 m

For reference junction compensation.

The application software can use only the measurement function.
(Logging function only)

USB adapter, USB cable and software

For protection of the main unit.

2 GB SD Memory Card

Used to hang the main unit on wall with rubber boot.

For hanging the main body during measurement

250 Ω resister, terminal adapter and leads

Magnet hook (Maximum weight 1.5 kg)

Used to connect an oscilloscope having a 1M-ohm input to a probe with a 50-ohm output. It is required when using the 701920 and 701922 probes with the DL1600 series.

Set contains one black and one red clip
1000 Vrms-CAT II
2 pieces (red and black) in 1 set 
Connected to the 758933, 758917, or 701901
Length: 0.3m
Applicable for DL750/DL750P, SL1000, SL1400

Improve switching-loss measurements by eliminating skew.  The 701936 Deskew Correction Signal Source accommodates both clamp-on current probes and through-type ‘CT' Current Transformers.

Connected to the 700929, 701947
Maximum input voltage: 1,000V (DC + ACpeak)
Length: 0.26m/0.3m/0.4m
Applicable for DL750/DL750P, SL1000, SL1400

Set contains one black and one red clip.
1000 Vrms-CAT II.

This DC block can be used to remove the DC component from an incoming signal. Use this block if you want to remove bias voltage from reaching the PBL5000 probe.

Carrying cases are useful for carrying and storing instruments.

For 720220 input terminal, one (1) piece

Screws for B8200JQ, D-SUB connector

10 Ω/0.25 W (×4)

(2 pcs./unit. order qty 1 unit)
The auxiliary earthing nets are used to improve the earthing conditions of the earth spikes. For example, on soft ground such as hard places such as concrete, etc. where the spikes cannot be driven.

A clip set designed for the 700988, 700960 and 701940 probes.

Attached to the tips of logic probe (701988 or 701989) or mini-clips (B9852CR), the IC clips can be used to clip contiguous 0.5-mm pitch terminals. A total of 10 clips are included.

The B9852HF contains the following eleven(11) kinds of accessories: Insulation cap, IC cap, BNC adapter, Rigid tip, Spring tip (Ø: 0.80 mm), Spring tip (Ø: 0.38 mm), Ground spring, Adjustment tool, Pincher tip, Standard ground lead, Color coding rings. PBL5000.

Accessory for GPS interface model (/C30)

Quality paper for the DL750P and the SL1400.
Paper width: 210 mm (A4 size)
Paper length: 20 m
Order Qty: 6 (1set)

Printer Paper Roll
Thermal paper (10m) for WT1600, WT 1800, WT3000, & WT3000E - 1 roll

Quality paper for the DLM6000/DL9700/DL9500/DL1700(E)/DL1600/DL1500 and DL7400

Quality paper for the DLM2000 /DLM4000 /DL850 /DL6000 /DL9000 and DL750

Battery cover for MT300

Soft Carrying Case

Soft Carrying Case

Shoulder Belt

Battery Pack

Battery pack (Spare)

For AQ4280A/AQ4280B/AQ4280C

For AQ2170 /AQ2170H /AQ2180 /AQ2180H /AQ4280A /AQ4280B /AQ4280C

For AQ2170/AQ2170H

For AQ2180 /AQ2180H /AQ4280A /AQ4280B /AQ4280C

For AQ2170/AQ2170H

For AQ2180 /AQ2180H /AQ4280A /AQ4280B /AQ4280C

Used by attaching to the main body.

Looking for more information on our people, technology and solutions?


Contact Us
Top