Cables

Extension cable for Clamp-on Probe

• 99014 Alligator Clip Leads
• 1000 V CAT III, 600 V CAT IV Red Black 1 set

for 96030, 96033

Total length: 2 m
USB2.0 Hi-Speed

Dedicated Cables for WT1800E /PD option.

Direct Current Input Cable (with Burden Resistor 2.7 Ohm) for WT1800E /PD2 option.

Direct Current Input Cable (without Burden Resistor) for WT1800E /PD2 option

Total length: 3 m/5 m/10 m

Circular 20 pin - D-sub 9 pin

2 pieces (red and black) in 1 set.
Length: 1.5 m, Rating: 80 A

2 voltage output cables (red and black). 1 m. Rating 1500 V
Use for circuits except Measurement Category II, III, IV.

For connection the external input of the WT3000 to the current sensor.
Length: 50cm

One set of 1 red and 1 black cables
Length: Approx. 1.0 m

Output cable for screw terminal, length approx.1 m

USB Cable (Type-C to Type-C)

1m PM100 connection cable

1 m in length, USB type A to USB type Micro-B.

For DL950,SL2000 multi-unit connection, 3 m

701905 Conversion Cable for Differential Probe

For SL1000, Cable length: 1 m

BNC-BNC 2m. To enable simultaneous measurement with 2 units or to carry an external trigger signal.

• 1 m long BNC to alligator clip cable
• Only for circuits with voltage levels no greater than 42 V

A subassembly of 1.2 m long test leads with alligator-clip adapters.
Use only for circuits having voltage levels no greater than 42 V.
Applicable for ScopeCorders.

This cable is used to connect an external device, however, do not use this cable for purposes other than DL750/1600/1700/1700E/7400 GO/NO-GO judgement.

• 701901 BNC to Safety Banana 1.8m Cable, 1:1
• 1000 Vrms-CAT II, 1.8 m long
• Safety BNC(male) to safety banana(female)
• 701959, 701954, 758921, 758922, 758929

• 701902/701903 Safety BNC to BNC Cable for oscilloscope
• Safe, high-voltage measurements with ScopeCorder isolated input modules 
• 701902: 1000 Vrms-CAT II (BNC-BNC), 1 m
• 701903: 1000 Vrms-CAT II (BNC-BNC), 2 m

1:1 Safety Adapter Lead for the 720268 High Voltage Input Module

For the DC power supply model (/DC). Cigarette lighter plug type.

• 701971 Alligator clip type for DL850EV ScopeCorder
• For the DC power supply model (/DC).

Applicable for ScopeCorder and WT300 series.

Connecting cable for 701953 (3 m)

• 366924 BNC to BNC cable for oscilloscope 
• 1m BNC wire
• Simultaneous measurement with 2 units
• Input external trigger signal

For SL1000, Cable length: 3 m

For DL850/E series, PX8000

• Set of 0.8m long red and black test leads
• Used with Power Analyzers and DMMs
• Used in combination with a pair of optional 758922 or 758929 alligator-clip adapters
• 1000 Vrms, 32 Arms CAT II

2 pieces (red and black) in 1 set
length: 1.00 m
Used in combination with the 701959, 758921, 758922, or 758929
Rating: 1000V CAT III/19 A

D-sub 9-pin (female)

One set of 1 red and 2 black cables
Length: Approx. 1.7 m

Alligator Clip Cable (Red x 3pcs, Black x 1pce 1 set/ 1.7m)

For use with the CA320, Alligator Clip Cable (Red Black 1 set/ 1.7m)

Alligator clip, CAT I, for controlsignal only (under 70 V)One set of 1 red and 1 black cablesLength: Approx. 1.7m

• 98073 Test Leads - Electrical Test Meter Leads | Yokogawa
• 1000 V CAT III 
• 600 V CAT IV
• Red/Black, 1 set

Output cable, length approx.1 m