Cables

• B9852MJ power probe extension cable
• Supplies power to 700924, 700925, and 701921 differential probes from the DL probe power connectors
• Required on DL unit
• Only works with newer probes

• Set of 0.8m long red and black multimeter test leads
• Used in combination with a pair of optional 758922 or 758929 alligator-clip adapters
• 1000 Vrms, 32 Arms CAT II

Applicable for DL850 and WT300 series.

2 pieces (red and black) in 1 set.
Length: 1.5 m, Rating: 80 A

Output cable, length approx.1 m

Output cable for screw terminal, length approx.1 m

For the DC power supply model (/DC). Cigarette lighter plug type.

For the DC power supply model (/DC). Allgator clip type.

• 701901 BNC to Safety Banana 1.8m Cable, 1:1
• 1000 Vrms-CAT II, 1.8 m long
• Safety BNC(male) to safety banana(female)
• 701959, 701954, 758921, 758922, 758929

• 701902/701903 Safety BNC to BNC Cable for oscilloscope
• Safe, high-voltage measurements with DL350, DL950, and SL1000 isolated input modules 
• 701902: 1000 Vtms-CAT II (BNC-BNC), 1 m
• 701903: 1000 Vrms-CAT II (BNC-BNC), 2 m

• 366924 BNC to BNC cable for oscilloscope 
• 1m BNC wire
• Simultaneous measurement with 2 units
• Input external trigger signal

• 1 m long BNC to alligator clip cable
• Only for circuits with voltage levels no greater than 42 V
• Applicable for DL750/DL750P, SL1000 & SL1400

This cable is used to connect an external device, however, do not use this cable for purposes other than DL750/1600/1700/1700E/7400 GO/NO-GO judgement.

A subassembly of 1.2 m long test leads with alligator-clip adapters.
Use only for circuits having voltage levels no greater than 42 V.
Applicable for SL1000 & SL1400.

BNC-BNC 2m. For connection to simultaneously measurement with 2 units, or for input external trigger signal.

1:1 Safety Adapter Lead for the 720268 High Voltage Input Module

2 voltage output cables (red and black). 1 m. Rating 1500 V

Dedicated Cables for WT1800E /PD option.

Direct Current Input Cable (with Burden Resistor 2.7 Ohm) for WT1800E /PD2 option.

Direct Current Input Cable (without Burden Resistor) for WT1800E /PD2 option

For connection the external input of the WT3000 to the current sensor.
Length: 50cm

2 pieces (red and black) in 1 set
length: 1.00 m
Used in combination with the 701959, 758921, 758922, or 758929
Rating: 1000 V CAT III/19 A

Alligator clip, CAT I, for controlsignal only (under 70 V)One set of 1 red and 1 black cablesLength: Approx. 1.7m

Alligator Clip Cable (Red x 3pcs, Black x 1pce 1 set/ 1.7m)

For use with the CA320, Alligator Clip Cable (Red Black 1 set/ 1.7m)

Extension cable for Clamp-on Probe

for 96030, 96033, 96036

1000 V CAT III, 600 V CAT IV Red Black 1 set

For DL850/E series, PX8000

For SL1000, Cable length: 1 m

For SL1000, Cable length: 3 m

Total length: 2 m
USB2.0 Hi-Speed

Connecting cable for 701953 (3 m)

One set of 1 red and 2 black cables
Length: Approx. 1.7 m

One set of 1 red and 1 black cables
Length: Approx. 1.0 m

D-sub 9-pin (female)

• 98073 Test Leads - Electrical Test Meter Leads | Yokogawa
• 1000 V CAT III 
• 600 V CAT IV
• Red/Black, 1 set

USB Cable (Type-C to Type-C)

1m PM100 connection cable

1 m in length, USB type A to USB type Micro-B.

For DL950 multi-unit connection, 3 m