The Model 2560A is a simple, precise and cost effective solution for calibrating DC measuring instruments such as analog meters, thermometers, temperature transmitters and data loggers
The 2560A Precision DC Calibrator offers high voltage and high current generation and intuitive operation for the analog meters calibration.
With output ranges of 100 mV to 1000 V and 100 µA to 30A, plus 10 different types of Thermocouples and Pt100 RTD, the 2560A can effectively solve the calibration requirements for DC Analog Meters and various temperature measuring instruments and controllers.
DC Voltage: ± 50 ppm
DC Current: ± 70 ppm
At 1 V and 1 mA range, for 180 days, 10 ppm = 0.001%
DC voltage: ±10 ppm/h
DC current: ±20 ppm/h
At 1 V and 1 mA range
5.5 digits, ±120000 count display
6.5 digits, ±1200000 count display*
*In the high resolution mode
DC voltage: −1224.00 V to +1224.00 V
DC current: −12.2400 A to +36.720 A
5 voltage ranges (100 mV, 1 V, 10 V, 100 V, 1000 V)
7 current ranges (100 μA, 1 mA, 10 mA, 100 mA, 1 A, 10 A, 30 A)
The maximum output is ±122.4% of range. An instrument’s 1200 V range can be calibrated.
To generate higher current than 36.72 A, two 2560As can be connected to double the output to 73.44 A.
Using the output divider and deviation
Calibrating two or more points is quick and simple. It is only necessary to preselect the number of required calibration points with the lower divider control and then use the upper control to step the output to the next calibration point. The deviation settings will then enable the output value and error of each calibration point to be displayed directly.
The deviation preset control can be used to move the output value in small increments (2 or 5% of the step between calibration points).
This means that it is possible to finely approach the target calibration point, either from a lower value or a higher one, without exceeding it. This is particularly useful when the friction (hysteresis) of the moving part needs to be taken into consideration. In this case the point is calibrated twice, once from a lower value and once more from a higher value and the final calibration result is the average of the two.
Needle sticking tests can be performed with high repeatability. It is possible to stop at any point and sweep around it in fine detail.
In the high resolution mode up to 6.5 digits, it is possible to test and calibrate digital multimeters and resistance standards.
*Sweep, divider, and deviation are not available in high resolution mode.
|Reduced energy, emission of CO2, NOx and SOx about 66% compared to the previous model.|
|Results of Life Cycle Assessment|
For reference junction compensation sensor. Pt100, 1.95 m
A set of 0.8m long red and black test leads, used in combination with a pair of optional 758922 or 758929 alligator-clip adapters.
Adapters for fitting a 4mm banana plug to a fork terminal. Set contains one black and one red clip. 1000 Vrms-CAT II.
Rated at 300 V. Attaches to the 758917 test leads. Sold in pairs.
Rated at 1000V. Attaches to the 758917 test leads. Sold in pairs.
2 pieces (red and black) in 1 set
length: 1.00 m
Used in combination with the 701959, 758921, 758922, or 758929
Rating: 1000 V CAT III/19 A
2 pieces (red and black) in 1 set.
Length: 1.5 m, Rating: 80 A
2 voltage output cables (red and black). 1 m. Rating 1500 V
2 safety terminal - alligator clip adapters (red and black). Rating 1500 V
RACK MOUNTING KIT For an EIA-compliant Single-housing Rack
RACK MOUNTING KIT For an JIS-compliant Single-housing Rack
Looking for more information on our people, technology and solutions?