Modules for DL708E/DL716 Digital Scopes (DISCONTINUED)

BNC-Banana-jack (female) adapter. Use for circuits having voltage levels no greater than 42 V.

• Differential oscilloscope probe
• 100 MHz
• ±1400 V (DC + ACpeak) at 1000:1
• Power: Internal battery or probe power supply
• Works with Oscilloscopes, ScopeCorders

15 MHz, 100:1/10:1, Max. Differential Voltage: ±500 V (DC + ACpeak) or 350 Vrms at 100:1 attenuation, Probe Power: Internal battery or probe power supply Work with Oscilloscopes, ScopeCorders

• 1000 V (DC+ACpeak), 100 MHz bandwidth
• Impedance (10 MΩ | 18 pF)
• CAT II rating, 1.7 m
•  
•  

• 8-bit, non-isolated, response speed: 1µs, threshold level approx 1.4V
• Leads (B9879PX and B9879KX) included.

• 8-bit, isolated; response: ≤1 ms (DC), ≤20 ms (AC); threshold: 6 VDC or 50 VAC.
• 758917 and 758922, 758929, 701954 

50 MHz, 1000:1/100:1, Max. Differential Voltage: 5000 Vrms/7000 Vpeak (1000:1), Probe Power: Internal battery or probe power supply B9852MJ power cable is bundled Work with Oscilloscopes, ScopeCorders

• 150 Arms maximum
• DC to 10 MHz bandwidth
• Interface: BNC

• 500 Arms maximum
• DC to 2 MHz bandwidth
• Interface: BNC

• 30 Arms maximum
• DC to 100 MHz bandwidth
• Interface: BNC
•  
•  

• 30 Arms maximum
• DC to 50 MHz bandwidth 
• Interface: BNC
•  
•  

• 701934 External Probe Power Supply
• Power supply for current probes, FET probes, and differential probes
• Supplies power for up to four probes, including large current probes

• 701919 oscilloscope probe stand
• Flexible arm, heavy base to hold and stabilize 8-13mm probes
• Can simplify circuit board testing

Banana-plug (male)-BNC adapter. Use for circuits having voltage levels no greater than 42 V.

T-adapter for BNC connectors. Use for circuits having voltage levels no greater than 42 V.

Safety-terminal-binding-post adapter. Use for circuits having voltage levels no greater than 42 V.

• 758921 Fork Terminal Adapters
• For fitting a 4mm banana plug to a fork terminal
• One black and one red clip
• 1000 Vrms-CAT II

Rated at 300 V. Attaches to the 758917 test leads. Sold in pairs.

Two adapters in a set (spring-hold type).

• Yokogawa 758929 Alligator Clip Adapter 
• Rated at 1000V
• Attaches to 758917 test leads
• Sold in pairs black/red

Screw-fastened adapters. Two adapters in a set. 1.5 mm Allen Wrench.

• B9852MJ power probe extension cable
• Supplies power to 700924, 700925, and 701921 differential probes from the DL probe power connectors
• Required on DL unit
• Only works with newer probes

A 1.5 m long connector-to-connector adapter cable complying with NDIS-MIL C26482. Used to connect a MIL-standard cable to the strain module

Convenient and practical for storing accessories (probes, etc). It can be attached to the DL750’s front panel protective cover.

• 1 m long BNC to alligator clip cable
• Only for circuits with voltage levels no greater than 42 V

A subassembly of 1.2 m long test leads with alligator-clip adapters.
Use only for circuits having voltage levels no greater than 42 V.
Applicable for ScopeCorders.

• Set of 0.8m long red and black test leads
• Used with Power Analyzers and DMMs
• Used in combination with a pair of optional 758922 or 758929 alligator-clip adapters
• 1000 Vrms, 32 Arms CAT II

For conversion between BNC and female banana plug
Applicable for ScopeCorder modules with BNC inputs.

• 366924 BNC to BNC cable for oscilloscope 
• 1m BNC wire
• Simultaneous measurement with 2 units
• Input external trigger signal

BNC-BNC 2m. For connection to simultaneously measurement with 2 units, or for input external trigger signal.