SOURCE MEASURE UNIT GS610

The GS610 is a highly accurate and highly functional programmable voltage/current source that incorporates voltage/current generation and measurement functions. The maximum output voltage and current are 110 V and 3.2 A, respectively. Evaluation of over a wide range of basic electrical characteristics is possible, because the GS610 can operate as a current source or a current sink.

Tm Gs610 25
  • USB STORAGE
  • V/I CURVE TRACER
  • ARBITARY WAVEFORM
  • WAVEFORM REPRODUCTION

            PDF Symbol Bulletin 7655-00E        PDF Symbol Leaflet 7656-30E

Get a Quote
Ask an Expert

 
 
This source measurement unit is fully performing to your high capacity needs and includes remote control and easy file operation for ease of use.

  • Source and sink operation up to 110 V/3.2 A (four-quadrant operation)
  • Basic accuracy: ±0.02% (DC voltage generation)
  • Sweep output at up to 100-µ intervals
  • Comes with abundant sweep patterns (linear, logarithmic, and arbitrary)
  • Stores up to 65535 points of source measure data in the internal memory
  • Remote control and FTP using Web server function (Optional)
  • Easy file operation with the USB storage function

Voltage/Current Generation and Measurement Range

Four-dimensional operation with source operation (current source) and sink operation (current sink) is possible at up to 110 V, 3.2 A, and 60 W.

The output and measurement resolutions are 5.5 digits.


Voltage generation/measurement range: 200 mV to 110 V
Current generation/measurement range: 20 µA to 3.2 A

Maximum output current:
±3.2 A & (at an output voltage of ±12 V or less)
±2 A (at an output voltage of ±30 V or less)
±1 A (at an output voltage of ±60 V or less)
±0.5 A (at an output voltage of ±110 V or less)

Generation and Measurement Functions

The GS610 is made up of a constant current source, a constant voltage source, a voltmeter, and an ammeter. Each function can be combined into numerous operation modes.


Operation modes:
  • Voltage generation/current measurement (VS/IM);
  • Voltage generation/voltage measurement (VS/VM);
  • Current generation/voltage measurement (IS/VM);
  • Current generation/current measurement (IS/IM);
  • Voltage generation (VS);
  • Current generation (IS);
  • Resistance measurement (VS/IM or IS/VM)

Additionally, control and measurement using a two-wire system or a four-wire system are possible by switching local sensing and remote sensing internally.

Tm Gs610 03



Various Operation Modes

 The voltage/current generation block of the GS610 operates in DC generation mode or pulse generation mode. Four operation modes-continuous output, linear sweep, log sweep, and program sweep-are available for each generation mode. In program sweep mode, the user can define an arbitrary sweep pattern. The output level can be changed at a minimum of 100 µs intervals in each sweep mode.

DC output mode
Tm Gs610 04

Pulse output mode
Tm Gs610 05

Generation and Measurement Timing

Source measure cycle (source & measure at 1 ms minimum)

As shown in the figure below, the GS610 is capable of synchronizing the generation and measurement at any operation mode. Generation is started after a source delay with respect to an internal/external trigger. Then, after the time it takes for the source level to stabilize (measure delay) the measurement is carried out over a given integration time. This function is necessary when making measurements by waiting for the load response after applying a pulse. The source measure cycle is the minimum unit for signal generation and measurement. The source/measurement operation (source measurement cycle) on the GS610 is 1 ms minimum.

Tm Gs610 06

Difference measurement using the sweep operation

The sweep operation can be used to make two measurements, then the difference between the two measurements can be determined. When the source value of sweep data 1 is established, the first measurement is carried out. Then, when the source value of sweep data 2 is established, the second measurement is carried out. The difference is determined by subtracting the value of the second measurement from that of the first measurement. By carrying out the two measurements within a short time, highly accurate measurements are possible with the effects of offset fluctuation cancelled. In addition, by applying a voltage with equal magnitude but opposite in polarity (source 1 = -1× source 2), the effects of offset error caused by the thermo electromotive force at the junction can be cancelled.


Tm Gs610 07

Zero Generation Function of Voltage and Current

The zero generation function of the GS610 enables the generation of the voltage/current zero value as well as the switching of the output condition between high and low impedance. In the zero generation condition, the voltage application or current supply to the load can be stopped with the output relay turned ON. This function avoids the problems of chattering and contact life of the output relay and reduces the ON/OFF operation time of the output.

Zero generation of voltage
- Low impedance: The current limiter is set to the specified value.
- High impedance: The current limiter is set to 0.5% of the range.

Tm Gs610 08

Zero generation of current
- Low impedance: The voltage limiter is set to 0.5% of the range.
- High impedance: The voltage limiter is set to the specified value.

Tm Gs610 09

External Input/Output and Synchronized Operation

The GS610 has various external input/output connectors. Signals such as the trigger input/output indicating the timing of generation and measurement, the output relay ON/OFF control signal, the zero generation ON/OFF control signal, and the comparator judgment result output can be input/output from the BNC and multi-core connectors. In addition, multiple GS610s can be synchronized by simply connecting the trigger output of a GS610 to the trigger input of another GS610 using a BNC cable.
(For the external view of the connector type, see the "Rear Panel" section on page 7.)

Tm Gs610 10



Signal Name Function    
TRIG IN TRIG input
SWEEP START IN
Sweep start input

CTRL IN
INTERLOCK Interlock input
OUTPUT Relay control input
ZERO Zero generation control input
TRIG OUT ORIGIN Trigger output
SOURCE CHANGE Source change timing output
MEASURE BEGIN Measure start timing output
MEASURE END Measure end timing output
PULSE END Pulse falling edge timing output

SWEEP SYNC OUT
ORIGIN Sweep synchronization output
TURN END Sweep 1 turn end timing output
ALL END Sweep all end timing output


CTRL OUT
INTERLOCK Interlock through output
OUTPUT Relay status output
ZERO Zero generation status output
PROGRAM Programmable output
COMPARE HI
Comparison result output HIGH
COMPARE IN
Comparison result output IN
COMPARE LO
Comparison result output LOW
COMPARE OV
Comparison result output OVERRANGE
COMPARE END
Compare END

Easy File Operation with the USB Storage Function

When the GS610 Source Measure Unit is connected to a PC via the USB, the PC detects the GS610 internal memory as a USB storage device. A pattern file can easily be stored in the GS610 internal memory by creating the GS610 generation pattern on a general-purpose worksheet application (1) and dragging and dropping the pattern file (2). The GS610 sweeps the voltage or current levels according to the generation pattern that is written in this file, measures the load current or load voltage at the appropriate points (3), and stores the results to the GS610 internal memory (4). There is absolutely no cumbersome programming or installation of dedicated software programs required (5) and (6).

Tm Gs610 11

User-Defined Computation Function

User-defined computation can be performed on the GS610 by combining dedicated operators. It can be used to carry out linear conversion of measured values, compute the power, compute the next generated value from the current measured value, and perform real-time computation of generated data using expressions. The expression is created using a text editor on your PC and stored to the GS610 internal memory via the USB.

Tm Gs610 12 Tm Gs610 13

Ethernet Interface (/C10 Option)


Remote control and file transfer can be carried out over the network by installing the Ethernet Interface (/C10 option).

Web Server
The GS610 connected via the Ethernet interface can be controlled from Internet Explorer.

  • Remote control
    Displays a front panel image of the GS610 on the browser with which the GS610 can be remotely controlled.
  • File transfer
    The GS610 internal memory can be handled as a PC file server. The output pattern can be transferred to the GS610 internal memory, or the measurement result data can be loaded in the PC.

Tm Gs610 14

Command control function

The GS610 can be controlled using commands similar to GP-IB or RS232 commands. Up to five clients can connect to the GS610.

Rear Panel

Tm Gs610 15

  • Trigger/sweep/control input (BNC connector)
    Select trigger input, sweep start input, or control input.
  • Trigger/sweep/control output (BNC connector)
    Select trigger output, sweep start output, or control output.
  • GP-IB
    An interface used to remotely control the GS610 from a PC (IEEE 488 compliant).
  • External input/output
    Synchronization control signal with other devices and comparator judgment result output.
  • Serial (RS-232)
  • Ethernet (/C10 option)
    Complies with 100BASE-TX/10BASE-T. Can be used to carry out FTP file transfer.
  • USB-PC connection
    Used to connect to a PC and enable the GS610 internal memory to operate as a USB storage device.
Name Description  
765670 Curve Tracer Software (Learn More) The high-speed, high-accuracy real-time V-I curve tracer consists of the GS Series Source Measure Unit and the 765670 Curve Tracer Software.

Learn More
LabVIEW Drivers for GS610 LabVIEW drivers for GS610 y-Link
TMCTL TMCTL is a DLL to support development of custom software. By using this DLL, users can write original programs to control instruments from a PC. y-Link
USB Driver The USB Driver is needed when required by the software. y-Link

1:1 BNC safety adapter lead 701901

1:1 BNC safety adapter lead 701901

1000 Vrms-CAT II, 1.8 m long
Safety BNC(male) to safety banana(female) use in combination with 701959, 701954, 758921, 758922 or 758929.

Safety BNC cable 701902/701903

Safety BNC cable 701902/701903

701902: 1000 Vtms-CAT II (BNC-BNC), 1 m
701903: 1000 Vrms-CAT II (BNC-BNC), 2 m

Safety mini clip (hook type) 701959

Safety mini clip (hook type) 701959

Set contains one black and one red clip. 1000 Vrms-CAT II.

Measurement lead set 758917

Measurement lead set 758917

A set of 0.8m long red and black test leads, used in combination with a pair of optional 758922 or 758929 alligator-clip adapters. Appliable for DL750/DL750P & SL1400.

Small Alligator-clip Adapter 758922

Small Alligator-clip Adapter 758922

Rated at 300 V. Attaches to the 758917 test leads. Sold in pairs.
Applicable for DL750/DL750P, SL1000, SL1400

Safety Terminal Adapter Set 758923

Safety Terminal Adapter Set 758923

Two adapters in a set (spring-hold type).

Conversion Adapter 758924

Conversion Adapter 758924

For conversion between BNC and female banana plug
Applicable for DL750/DL750P, SL1000 & SL1400.

Large Alligator-clip Adapter 758929

Large Alligator-clip Adapter 758929

Rated at 1000V. Attaches to the 758917 test leads. Sold in pairs.
Applicable for DL750/DL750P, SL1000, SL1400.

Safety Terminal Adapter Set 758931

Safety Terminal Adapter Set 758931

Screw-fastened adapters. Two adapters in a set. 1.5 mm Allen Wrench.

 

All Products Guide
All Products Guide
PDF (10.26 MB)
CALL TOLL-FREE AT
1-800-888-6400
(8:00 TO 17:00 EASTERN)
y-Link