The SL1000 is a modular data acquisition system that delivers independent, isolated channel hardware at high speeds up to 100 MSamples per channel, with no compromise in bit resolution, memory depth, or data streaming performance. Choose from a wide variety of I/O modules for electrical and physical sensor signal measurements to meet the needs of any high channel count application.
Selecting a data acquisition platform for electronics or mechatronics applications has always been a balancing act. High speed digitizers lack the isolation, attenuation, or bit resolution necessary for power electronics testing. PC-based platforms with fast streaming throughput sacrifice noise immunity, signal conditioning, and hardware integrity.
Until now. The new Yokogawa SL1000 is the only data acquisition system that delivers independent, isolated channel hardware at 100MS/ch rates, with no compromise in bit resolution, memory depth, or streaming performance.
¹: In combination with 10:1 probe (for isolated BNC input) model 702902 or 700929
²: Optional
³: Speed depends on PC performance and measuring conditions.
In the pursuit of isolated high-speed waveform measurements, Yokogawa has achieved a maximum sample rate of 100 MS/s (10 ns sampling interval). The SL1000 can accurately capture high-speed and high-voltage phenomena by using the newly developed 100 MS/s, 12-Bit resolution, 20 MHz frequency range and 1-kV * Isolation Module (model 720211).
Furthermore, you can combine modules that support measurements of a variety of signals, giving you solutions for an extensive range of applications.
*: In combination with 10:1 probe (for isolated BNC input ) model 702902 or 700929
Data can be saved to the SL1000’s internal acquisition memory over long durations, or it can also be streamed in real-time to a PC's hard disk or the SL1000’s internal hard disk ¹ ².
¹: with the /HD1 Option
²: Maximum speed of real time hard disk recording depends on measuring conditions.
³: Trigger mode: Single, measuring on 1 module, 2 channels.
Perform measurements with up to four simultaneously independent sample rates. The amount of data saved on hard disk can be reduced by optimizing the sample rate for the DUT on a module by module basis.
You can transfer data to the PC at high speeds via USB 2.0 or Ethernet 1000BASE-T Gigabit Ethernet¹. The SL1000’s high-speed data compression engine (GIGAZoom engine) displays waveforms on the PC in real time² (even with massive amounts of data at high sample rates). It offers the same display updating and zooming performance as standalone measuring instruments.
¹: with the /C10 Option
²: The number of channels from which waveforms can be displayed during measurement may be limited depending on the PC performance and measuring conditions.
Continuously measured data can be saved in real time to a PC's hard disk and/or the SL1000's internal hard disk ¹. File names are assigned automatically, freeing you from time consuming file operations. Data can be saved simultaneously - and in real time - to both the PC’s and SL1000's hard disks ¹. This bolsters the reliability of your data storage system, protecting your vital data. You can access the SL1000's internal hard disk ¹ with Xviewer waveform viewer software, or through an FTP client over Ethernet ².
¹: with the /HD1 Option
²: with the /C10 Option
³: Typical values. Actual values depend on PC performance and measurement conditions.
By using the various recording features, you can efficiently and automatically record only the data you need to the hard disk. Just specify the recording destination, recording start and stop conditions, conditions for repeating recording, and other criteria. With free run mode, the specifiable parameters for the recording start condition are immediate, time, and alarm; for the recording stop condition, the parameters are continuous, time, recording time, and alarm; and for the repeating condition, recording interval and number of recordings*. With triggered mode, measured data is recorded on each trigger. You can also manually save data from the SL1000's internal acquisition memory to PC hard disk.
*: Max. file size per recording is 12 GB (recording on 4 channels, approximately 1.5 GW/ch)
Maximum 8 Synchronized Units
1: Typical values. Actual values depend on PC performance and measurement conditions
(Note)
In synchronized unit mode, recording into PC and SL1000 embedded HDD at the same time is not possible.
The recording file is per unit basis. (Utility software interface.)
You can input the comments in the mark area when monitoring (Free run mode) over long periods of time.
You can now see both the T-Y and X-Y waveform Display. It is easy to evaluate data with fast update.
It is easy to set zoom position of waveform when measuring over long periods of time data or large data.
You can save the data in both ASCII and Binary format. You can also load data with the same analysis program (ex. MATLAB).
Setting Operation Display
You can easily detect unevenness or changes in acquired data.
The Wizard automatically recognizes any connected SL1000 and its' plug-in modules. Just click the Start button to start measuring right away - no complicated settings to enter. The four screens of the Setup Wizard guide you easily through detailed settings for configuring the system, measuring, saving and displaying. Of course, you can save and recall your settings at any time.
Up to four groups of measurement channels can be defined with individual measurement conditions and display settings. Even waveforms from groups with different sample rates can be displayed in the same window.
Measurement conditions and channel display settings can be viewed and set easily using a tabular format. Use drag and drop shortcuts to quickly setup multiple channels.
Measurement condition setting screen Display setting screen
Measurement and saving can be started and stopped using the same familiar buttons found on a DVD remote control. Start using the instrument on the same day you receive it, with absolutely no programming required.
You can display a zoomed portion of the waveform simultaneously with the overall waveform during triggered measurement. Even during live recording, you can use the display hold * to review past data. You can also perform cursor measurements or automated measurement of waveform parameters (up to 26 during triggered measurement) in real time.
*: The display hold may automatically switch to display resume depending on the measuring conditions.
Adjust your vertical display scale with ease using mouse shortcuts.
Adjust your vertical display scale with ease using mouse shortcuts.The File Transfer Function transfers files from the SL1000 to PC via, the Acquisition Software, intelligently in the case of multiple synchronized units.
SL1000 File Utility is file processing software for manipulating acquired files before analyzing waveforms with Xviewer. It can also analyze multiple channels across several units at the same time.
* SL1000 File Utility is bundled with the SL1000 standard install CD.
Xviewer is a PC software application designed to work with Yokogawa’s digital oscilloscopes and ScopeCorders.
MATLAB WDF Access Toolbox enables the access to waveform data files saved in WDF format on MATLAB.
To control the instruments on MATLAB, please use Instrument Control Toolbox provided by MathWorks.
High-Speed 100 MS/s 12-Bit Isolation Module (2 channels)
IsoPRO technology enables 1kV isolated measurements in combination with 700929 or 701947 probe and is designed for inverter / IGBT related applications in mind. Using high speed optical fiber-based transmission, the module achieves high speed ADC clock and data isolation and provides the performance needed to develop high efficiency inverters, which employ high voltages, large currents, and ever increasing switching speeds.
Applicable to DL350, DL850 series and SL1000.
The 720250 Voltage Module has a 10 MS/s sample rate, 12-bit resolution, 3 MHz bandwidth, 2 isolated channels, a maximum input voltage (DC+ACpeak) of 800 V*2, 200 V*3, DC accuracy of ±0.5%, and high noise immunity.
Applicable to DL350, DL850 series and SL1000.
High-Speed 1 Ms/s 16-Bit Isolation Module (2 ch)
High sensitivity range (10 mV), low noise (±100 µVtyp), and high noise immunity
Applicable to DL850 series, DL750 series and SL1000.
High-Speed 10 MS/s 12-Bit non-isolation Module (2 ch)
Non-Isolation version of model 720250
Applicable to DL850 series, DL750 series and SL1000.
The 720268 High Voltage Module has a 1 MS/s sample rate, 16-bit resolution, 300 kHz bandwidth, 2 isolated channels, a maximum input voltage (DC+ACpeak) of 1000V*9 *11, DC accuracy of ±0.25%, and AAF, RMS, and high noise immunity.
Applicable to DL350, DL850 series and SL1000.
Universal Module (2 ch)
Thermocouple (K, E, J, T, L, U, N, R, S, B, W, iron-doped gold/chromel)
Applicable to DL350, DL850 series, DL750 series and SL1000.
Universal Module (with Anti-Aliasing Filter, 2 ch)
Thermocouple (K, E, J, T, L, U, N, R, S, B, W, iron-doped gold/chromel), with AAF
Applicable to DL350, DL850 series, DL750 series and SL1000.
Temperature/high-precision voltage Module (2 ch)
Thermocouple (K, E, J, T, L, U, N, R, S, B, W, iron-doped gold/chromel), high sensitivity range (1 mV), and low noise (±4 µVtyp)
Applicable to DL350, DL850 series, DL750 series and SL1000.
The 720266 Module has a 125 S/s (Voltage) and 125 S/s (Temperature) sample rate. It has a 16-Bit (Voltage),
0.1°C (Temperature) resolution, 15 Hz bandwidth, 2 isolated channels, a maximum input voltage (DC+ACpeak) of 42V, DC accuracy of ±0.08% (Voltage), and thermocouple (K, E, J, T, L, U, N, R, S, B, W, iron-doped gold/chromel), high sensitivity range (0.1 mV/div), and low noise (±4 µVtyp.).
Applicable to DL350, DL850 series and SL1000.
Strain Module, type NDIS (2 channels) to be used in combination with 701955 or 701956 NDIS bridge head.
Using the strain module and strain gauge the ScopeCorder can detect and display mechanical stress (strain). It works on the principle that the resistance value of a metal foil changes as it expands and contracts.
Applicable to DL350, DL850 series, DL750 series and SL1000.
Strain Module with Shunt Calibration, type DSUB (2 channels) to be used in combination with 701957 or 701958 DSUB bridge head.
Using the strain module and strain gauge the ScopeCorder can detect and display mechanical stress (strain). It works on the principle that the resistance value of a metal foil changes as it expands and contracts.
Applicable to DL350, DL850 series, DL750 series and SL1000.
Acceleraton/Voltage Module with Anti-Aliasing Filter, (2 channels)
Accepts direct input from a built-in amp type acceleration sensor to measure acceleration. Sensor supply current (voltage) OFF/4 mA ± 10% (approx. 22 VDC) Applicable acceleration sensor type: Built-in amplifier type, Kistler Instruments Corp. : PiezotronTM, PCB, Piezotronics Inc. : ICPTM, Endevco Corp : IsotronTM.
Applicable to DL350, DL850 series and SL1000.
The 720281 Frequency Module has a 1 MS/s sample rate, 16-bit resolution, bandwidth of resolution 625 ps, 2 isolated channels, a maximum input voltage (DC+ACpeak) of 420 V*2, 42 V*3, DC accuracy of ±0.1% (Frequency), and measurement frequency of 0.01 Hz to 500 kHz. The measured parameters are frequency, rpm, period, duty, power supply frequency, distance, and speed.
Applicable to DL350, DL850 series and SL1000.
200 MHz, 100:1, Isolated BNC, ±1000 V (DC + ACpeak) CAT II ±3540 V (DC + AC peak) CAT I, 1.5 m
For ScopeCorder Isolated Modules
Passive Probe, 1000V(DC+ACpeak) CAT II, 60MHz, 10:1, 10MΩ, 2.5m
Wide operating temperature range(-40 to 85°C)
For isolated BNC input modules for ScopeCoder series
Passive Probe, 1000Vp CAT II, 100MHz, 10:1, 10MΩ, 1.5m, Isolated Probe, Iso-Probe
Please see also 701947 & accessories.
10 MHz, 10:1/1:1, 600 V (DC + ACpeak) CAT II, 1.5 m
For ScopeCorder Non-Isolated Modules
100 MHz, 1000:1/100:1, Max. Differential Voltage: ±1400 V (DC + ACpeak) at 1000:1, Probe Power: Internal battery or probe power supply Work with Oscilloscopes, ScopeCorders
Works with Oscilloscopes, ScopeCorders. 15 MHz, 100:1/10:1, Max. Differential Voltage: ±500 V (DC + ACpeak) or 350 Vrms at 100:1 attenuation, Probe Power: Internal battery or probe power supply.
50 MHz, 1000:1/100:1, Max. Differential Voltage: 5000 Vrms/7000 Vpeak (1000:1), Probe Power: Internal battery or probe power supply B9852MJ power cable is bundled Work with Oscilloscopes, ScopeCorders
Frequency bandwidth: DC to 50 MHz
Maximum continuous input range: 5 Arms
Functions with Digital Oscilloscopes, ScopeCorders and other waveform measuring instruments.
Frequency bandwidth: DC to 120 MHz
Maximum continuous input range: 5 Arms
Functions with Digital Oscilloscopes, ScopeCorders and other waveform measuring instruments.
Current probe powered by Yokogawa Digital Oscilloscopes, Scopecorders or external power supply.
Current probe powered by Yokogawa Digital Oscilloscopes, Scopecorders or external power supply.
Current probe powered by Yokogawa Digital Oscilloscopes, Scopecorders or external power supply.
Current probe powered by Yokogawa Digital Oscilloscopes, Scopecorders or external power supply.
The 720930 and 720931 passive clamp-on current probes allow current waveform readings directly via analog input modules on ScopeCorders including the DL350 and DL850 using isolated BNC connections.
The 720931 passive clamp-on current probe anables current waveform readings directly via analog input modules on ScopeCorders including the DL350 and DL850 using isolated BNC connections.
A power supply for current probes, FET probes, and differential probes. Supplies power for up to four probes, including large current probes.
The B9852MJ cable supplies power to the 700924, 700925 and 701921 differential probes* from the DL probe power con-nectors. (The probe power option is re-quired on the DL unit.)
* Cable only works with newer 700924, 700925 and 701921 probes that indicate "6VDC or 9VDC"at the probe input power connector.
701955 NDIS Bridge Head, Bridge resistance: 120Ω , 5m NDIS cable included
701956 NDIS Bridge Head, Bridge resistance: 350Ω , 5m NDIS cable included
701957 DSUB Bridge Head with Shunt calibration
Bridge resistance: 120Ω , 5m DSUB cable included
701958 DSUB Bridge Head with Shunt calibration
Bridge resistance: 350Ω , 5m DSUB cable included
T-adapter for BNC connectors. Use for circuits having voltage levels no greater than 42 V.
Safety-terminal-binding-post adapter. Use for circuits having voltage levels no greater than 42 V.
For conversion between BNC and female banana plug
Applicable for DL750/DL750P, SL1000 & SL1400.
For 702902, 702906
A set of 0.8m long red and black test leads, used in combination with a pair of optional 758922 or 758929 alligator-clip adapters.
2 pieces (red and black) in 1 set
length: 1.00 m
Used in combination with the 701959, 758921, 758922, or 758929
Rating: 1000 V CAT III/19 A
1000 Vrms-CAT II, 1.8 m long
Safety BNC(male) to safety banana(female) use in combination with 701959, 701954, 758921, 758922 or 758929.
Set contains one black and one red clip
1000 Vrms-CAT II
2 pieces (red and black) in 1 set
Connected to the 758933, 758917, or 701901
Length: 0.3m
Applicable for DL750/DL750P, SL1000, SL1400
Connected to the 700929, 701947
Maximum input voltage: 1,000V (DC + ACpeak)
Length: 0.26m/0.3m/0.4m
Applicable for DL750/DL750P, SL1000, SL1400
Set contains one black and one red clip.
1000 Vrms-CAT II.
Rated at 1000V. Attaches to the 758917 test leads. Sold in pairs.
Rated at 300 V. Attaches to the 758917 test leads. Sold in pairs.
Adapters for fitting a 4mm banana plug to a fork terminal. Set contains one black and one red clip. 1000 Vrms-CAT II.
Screw-fastened adapters. Two adapters in a set. 1.5 mm Allen Wrench.
701902: 1000 Vtms-CAT II (BNC-BNC), 1 m
701903: 1000 Vrms-CAT II (BNC-BNC), 2 m
BNC-BNC 1m. For connection to simultaneously measurement with 2 units, or for input external trigger signal.
BNC-BNC 2m. For connection to simultaneously measurement with 2 units, or for input external trigger signal.
A 1 m long BNC-alligator clip cable.
Use only for circuits having voltage levels no greater than 42 V.
Applicable for DL750/DL750P, SL1000 & SL1400
A subassembly of 1.2 m long test leads with alligator-clip adapters.
Use only for circuits having voltage levels no greater than 42 V.
Applicable for SL1000 & SL1400.
Using a probe stand with a flexible arm and heavy base to hold and stabilize probes can simplify circuit board testing.
For SL1000 (EIA)
For SL1000 (JIS)
Observation of Inverter Switching Waveforms
There are several factors for a user to consider when using an IEPE accelerometer, particularly when used with newly available integrated signal conditioner/data acquisition systems. Correctly managing these factors will help the user avoid erroneous data from their IEPE accelerometer and ensure the quality of the measurement data is at the level they expect and require.
Surge Waveform Recording & Power Monitoring
With increased focus on reducing energy consumption and compliance with efficiency standards, this app note provides an overview on the types of measurements needed for efficiency and power quality, and the instruments that take them.
The objective of this paper is to show the close relationship between efficiency and power quality, and provide education on the causes of power quality, types of power quality issues, and provide guidance on measurement considerations.
In the oscilloscope's QIS (Quality Inspection Standards), the "beat method" can be used to inspect and verify the time base accuracy. The "beat method" utilizes the aliasing effect to create a "beat waveform." The "beat ...
This training module covers the following topics: