Error(Code:846) Occurs When Attempting to Start Integration on the WT3000
Resources:
"Error(Code:846): Attempted to start integration while measurement of peak overflow was in progress"
The following error code will appear if Peak Over has occurred and you attempt to start integration. The WT3000 has two types of indicators, Over Range and Peak Over, which are used to indicate when a measurement value has exceeded the limit range.
Over Range Indicator
When the crest factor(CF) is set to 3, the WT3000 can measure up to three times the RMS range value. When the CF is 6, the WT3000 can measure up to six times the RMS range value. If the RMS value of the input waveform is larger than the setting of the range value, the WT3000 shows Over Range or --OL--. In this case, integration can still be started and no error will occur.
Peak Over Indicator
The following error code will appear if Peak Over has occurred and you attempt to start integration. The WT3000 has two types of indicators, Over Range and Peak Over, which are used to indicate when a measurement value has exceeded the limit range.
Over Range Indicator
When the crest factor(CF) is set to 3, the WT3000 can measure up to three times the RMS range value. When the CF is 6, the WT3000 can measure up to six times the RMS range value. If the RMS value of the input waveform is larger than the setting of the range value, the WT3000 shows Over Range or --OL--. In this case, integration can still be started and no error will occur.
Peak Over Indicator
The peak value of a sine wave can be calculated using the following formula:
Vpeak= Vrms x 1.4142
The Peak Over indicator illuminates red if the measured value of the input waveform is larger than three times the range value (CF=3) or six times the range value (CF=6). If Peak Over has occurred, but the measured RMS value of the input waveform has not exceeded the RMS range, Error 846 will occur.
Note:
Vpeak= Vrms x 1.4142
The Peak Over indicator illuminates red if the measured value of the input waveform is larger than three times the range value (CF=3) or six times the range value (CF=6). If Peak Over has occurred, but the measured RMS value of the input waveform has not exceeded the RMS range, Error 846 will occur.
Note:
- If you supply current exceeding approximately 2.8Arms to the 2-A input element, the protection circuit activates and bypasses the measurement circuit of the WT3000. The Peak Over indicator at the top section of the screen will illuminate red. The measured value will display approximately 0 A, but current is actually flowing through the circuit under measurement. Therefore, DO NOT disconnect the wires to the measurement terminals.
- The Peak Over range indicator may not illuminate or blink in the following cases.
1. If the pulse width is narrow, and the peak value of the waveform cannot be acquired at the sampling rate of the WT3000 (approximately 200 ks/s).
2. If the high frequency components of the pulse waveform attenuate due to the bandwidth limiting by the WT3000 measurement circuit and the waveform peak value is less than the Peak Over range detection level.
相关产品和解决方案
高精度功率分析仪 WT3000
WT3000高精度功率分析仪提供最高精度的测量。此产品已成为行业标准，用于变频器、电机驱动器、照明系统和电子镇流器、UPS系统、飞机电力系统、变压器测试和其它电力转换设备的研发。WT3000的基本功率精度达0.02%，带宽为1MHz。
数字功率分析仪
功率计或称瓦特计，可以测量产生、转换或消耗电能的设备各项特征，包括设备的各项参数，如：功率（瓦特）、功率因数、谐波和效率等等。
YOKOGAWA数字功率分析仪，性能优越、测量可靠，支持各种应用，非常值得拥有。尤其是YOKOGAWA WT300E功率计，在全球功率计市场上口碑与地位日益跃升。
返回顶部
微信扫一扫
获得更多专业服务
获得更多专业服务