Yokogawa offers a range of oscilloscope accessories, including rack mount kits, probe accessories, BNC cables, alligator clips, carrying cases, and more. Our variety of accessories for oscilloscopes provide everything you need to connect to your signals.
Three pockets are provided for storing accessories and the user’s manual.
Three pockets are provided for storing accessories and the user’s manual.
Three pockets are provided for storing accessories and the user’s manual.
A power supply for current probes, FET probes, and differential probes. Supplies power for up to four probes, including large current probes.
1000 Vrms-CAT II, 1.8 m long
Safety BNC(male) to safety banana(female) use in combination with 701959, 701954, 758921, 758922 or 758929.
A set of 0.8m long red and black test leads, used in combination with a pair of optional 758922 or 758929 alligator-clip adapters.
Adapters for fitting a 4mm banana plug to a fork terminal. Set contains one black and one red clip. 1000 Vrms-CAT II.
Rated at 1000V. Attaches to the 758917 test leads. Sold in pairs.
Rated at 300 V. Attaches to the 758917 test leads. Sold in pairs.
Set contains one black and one red clip.
1000 Vrms-CAT II.
701902: 1000 Vtms-CAT II (BNC-BNC), 1 m
701903: 1000 Vrms-CAT II (BNC-BNC), 2 m
A 1 m long BNC-alligator clip cable.
Use only for circuits having voltage levels no greater than 42 V.
Applicable for DL750/DL750P, SL1000 & SL1400
A subassembly of 1.2 m long test leads with alligator-clip adapters.
Use only for circuits having voltage levels no greater than 42 V.
Applicable for SL1000 & SL1400.
BNC-BNC 1m. For connection to simultaneously measurement with 2 units, or for input external trigger signal.
BNC-BNC 2m. For connection to simultaneously measurement with 2 units, or for input external trigger signal.
BNC-Banana-jack (female) adapter. Use for circuits having voltage levels no greater than 42 V.
Banana-plug (male)-BNC adapter. Use for circuits having voltage levels no greater than 42 V.
T-adapter for BNC connectors. Use for circuits having voltage levels no greater than 42 V.
Safety-terminal-binding-post adapter. Use for circuits having voltage levels no greater than 42 V.
Quality paper for the DLM6000/DL9700/DL9500/DL1700(E)/DL1600/DL1500 and DL7400
Quality paper for the DL750P and the SL1400.
Paper width: 210 mm (A4 size)
Paper length: 20 m
Order Qty: 6 (1set)
701957 DSUB Bridge Head with Shunt calibration
Bridge resistance: 120Ω , 5m DSUB cable included
701958 DSUB Bridge Head with Shunt calibration
Bridge resistance: 350Ω , 5m DSUB cable included
A 1.5 m long connector-to-connector adapter cable complying with NDIS-MIL C26482. Used to connect a MIL-standard cable to the strain module
701955 NDIS Bridge Head, Bridge resistance: 120Ω , 5m NDIS cable included
701956 NDIS Bridge Head, Bridge resistance: 350Ω , 5m NDIS cable included
Connected to the 700929, 701947
Maximum input voltage: 1,000V (DC + ACpeak)
Length: 0.26m/0.3m/0.4m
Applicable for DL750/DL750P, SL1000, SL1400
Set contains one black and one red clip
1000 Vrms-CAT II
2 pieces (red and black) in 1 set
Connected to the 758933, 758917, or 701901
Length: 0.3m
Applicable for DL750/DL750P, SL1000, SL1400
This cable is used to connect an external device, however, do not use this cable for purposes other than DL750/1600/1700/1700E/7400 GO/NO-GO judgement.
This DC block can be used to remove the DC component from an incoming signal. Use this block if you want to remove bias voltage from reaching the PBL5000 probe.
Used to connect an oscilloscope having a 1M-ohm input to a probe with a 50-ohm output. It is required when using the 701920 and 701922 probes with the DL1600 series.
For the DC power supply model (/DC). Allgator clip type.
For the DC power supply model (/DC). Cigarette lighter plug type.
Attached to the tips of logic probe (701988 or 701989) or mini-clips (B9852CR), the IC clips can be used to clip contiguous 0.5-mm pitch terminals. A total of 10 clips are included.
Improve switching-loss measurements by eliminating skew. The 701936 Deskew Correction Signal Source accommodates both clamp-on current probes and through-type ‘CT' Current Transformers.
Using a probe stand with a flexible arm and heavy base to hold and stabilize probes can simplify circuit board testing.
The B9852HF contains the following eleven(11) kinds of accessories: Insulation cap, IC cap, BNC adapter, Rigid tip, Spring tip (Ø: 0.80 mm), Spring tip (Ø: 0.38 mm), Ground spring, Adjustment tool, Pincher tip, Standard ground lead, Color coding rings. PBL5000.
Convenient and practical for storing accessories (probes, etc). It can be attached to the DL750’s front panel protective cover.
The B9852MJ cable supplies power to the 700924, 700925 and 701921 differential probes* from the DL probe power con-nectors. (The probe power option is re-quired on the DL unit.)
* Cable only works with newer 700924, 700925 and 701921 probes that indicate "6VDC or 9VDC"at the probe input power connector.
Two adapters to a set for 5 A current
(screw-fastened type using B9317WD)
After a disastrous 2009, the large publicly held test companies enjoyed booming business in 2010.
The definition of a high-performance oscilloscope really is all about the customer's point of view. Two scopes may have the same bandwidth, number of channels, sampling rate, operating modes, and memory length. Yet, one will be bought instead of the other because its software or triggering capability or measurement suite better matches the customer's application requirements.
The definition of a high-performance oscilloscope really is all about the customer's point of view. Two scopes may have the same bandwidth, number of channels, sampling rate, operating modes, and memory length. Yet, one will be bought instead of the other because its software or triggering capability or measurement suite better matches the customer's application requirements.