Communication Sample Programs

Description

The following programs are communication sample programs written in Visual Basic (VB) and Visual C++ (VC++)'s project format. Please refer to the User's Manual(IM 701990-01E) for detailed information, which can be extracted from "dlsample106.zip" file.

  • System Requirements:
    Visual basic (VB) and Visual C++ (VC++) on the Windows operating system.
    (National Instruments GP-IB board or PCMCIA card is required when using GP-IB interface.)
  • Supported models:
    DL9000 series ,DL7000 sereis, DLM6000/DL6000 series, DLM4000 series, DLM2000 series, DL1700E series, DL1700 series, DL1600 series, SB5000, DL750 series, DL850 series, SL1400
  • Software, driver requirements:
    "TMCTL", which is the Yokogawa original driver software, is required to use these sample programs. Download here. A dedicated USB driver is required when using USB interface. The USB driver can be downloaded from here.
  • Supported communication interfaces:
    Ethernet, USB, GP-IB and SERIAL

Applicable Model

dlsample106.zip
Applicable models:DL850/DL750/DL7400/SL1400/DLM2000/DLM4000 series 

DL9000Sample105.zip
Applicable model: DL9000 series, DL6000/DLM6000 series and SB5000

Download

 

Please read Software Agreement carefully before downloading.

 

Release Date Jan 31, 2013
File Name dlsample106.zip 1.1 MB

  

DL9000Sample105.zip 1.0 MB

  

Type Software

 

* Software Agreement
  • The property rights, proprietary rights, intellectual property rights, and all other rights associated with the software are held by Yokogawa Test & Measurement Corporation.
  • Under no circumstances is any dumping, reverse compiling, reverse assembly, reverse engineering, or any other kind of alteration or revision of this software allowed.
  • This software is offered free of charge, but no unlimited warranties are made against any defects whatsoever.
  • Also, Yokogawa may not be able to accept inquiries regarding repair of defects in or questions about this software.
  • The contents of this software are subject to change without prior notice as a result of continuing improvements to the software's performance and functions.
  • Yokogawa bears no liability for any problems that may occur during download or installation of this software.
  • Use of the Yokogawa Web site is at the user's own risk.
  • Any parties contributing to the creation or distribution of the contents on the Yokogawa Web site shall bear no responsibility whatsoever for any damages occurring as a result of the use of said contents.

Downloading of the software indicates acceptance of the software agreement.

Related Products & Solutions

DL7440/DL7480 Digital Oscilloscopes

8-channel 500 MHz oscilloscope with 16 logic inputs, for applications where four channels aren't enough.  Support for eight analog channels, 16 bits with 250MHz logic bandwidth, 16MP of recording memory, power analysis, serial bus analysis, and a broad selection of voltage and current probes.

DL750/DL750P ScopeCorder

The DL750 ScopeCorder: A new measurement tool combining the functions of an oscilloscope for capturing instantaneous phenomena and a data recorder for monitoring long-term trends.

DL9000 DSO Series

500MHz, 1.0GHz, and 1.5GHz DSOs for debug and high performance applications. 10th
generation oscilloscope from Yokogawa with industry leading 2.5 million wfms/sec and lowest dead time. Winner of Test & Measurement World's "Best in Test" award.

DLM6000 MSO & DSO Series

500MHz, 1.0GHz, and 1.5GHz DSO and MSO models for debug, waveform characterization, bench top, or automated test applications. 4 channel models with 16 or 32 logic inputs. 12th generation oscilloscope with ergonomic physical and on-screen improvements.

SB5000 Vehicle Serial Bus Analyzer

1.0GHz MSOs optimized for parallel and serial bus design and debug. Supports CAN bus, LIN, FlexRay, I2C, SPI, UART, and user-defined busses.  Display, decode, analyze, search, and trigger on popular serial bus attributes.

 
Top