SL1000 High Channel Count ScopeCorder DAQ
The SL1000 is a modular data acquisition system that delivers independent, isolated channel hardware at high speeds up to 100 MSamples per channel, with no compromise in bit resolution, memory depth, or data streaming performance. Choose from a wide variety of I/O modules for electrical and physical sensor signal measurements to meet the needs of any high channel count application.
Selecting a data acquisition platform for electronics or mechatronics applications has always been a balancing act. High speed digitizers lack the isolation, attenuation, or bit resolution necessary for power electronics testing. PC-based platforms with fast streaming throughput sacrifice noise immunity, signal conditioning, and hardware integrity.
Until now. The new Yokogawa SL1000 is the only data acquisition system that delivers independent, isolated channel hardware at 100MS/ch rates, with no compromise in bit resolution, memory depth, or streaming performance.
Speed of managing and acquiring data is the highlight of the SL1000.
- Fast Acquisition
- Up to 100 MS/s on all channels (10 ns sampling interval)
- 100 MS/s 12-Bit 1 kV¹ isolation module with 20 MHz bandwidth
- Supports parallel testing: Perform measurements with up to four simultaneously independent sample rates
- Fast Transfer and Storage
- Stream data to PC via high speed USB 2.0 or 1000BASE-T Gigabit Ethernet²
- Real time display on a PC (GIGAZoom engine)³
- Stream data to a PC hard disk or the SL1000's internal hard disk² in real time (at speeds of 1.6 MS/s = 100 kS/s x 16ch)³
- Easy to use
- Easy to use Standard Acquisition Software
- Quick and Intuitive operation means that you can start measuring immediately
- Setup Wizard guides you through detailed settings
- Can operate "Standalone"
- Store data directly on the SL1000
- Wide Library of Plug-In Modules
- Eight module slots are available in each unit
- Select from twelve different plug-in modules
¹: In combination with 10:1 probe (for isolated BNC input) model 702902 or 700929
²: Optional
³: Speed depends on PC performance and measuring conditions.
High-Speed Capture
In the pursuit of isolated high-speed waveform measurements, Yokogawa has achieved a maximum sample rate of 100 MS/s (10 ns sampling interval). The SL1000 can accurately capture high-speed and high-voltage phenomena by using the newly developed 100 MS/s, 12-Bit resolution, 20 MHz frequency range and 1-kV * Isolation Module (model 720211).
Furthermore, you can combine modules that support measurements of a variety of signals, giving you solutions for an extensive range of applications.
*: In combination with 10:1 probe (for isolated BNC input ) model 702902 or 700929
Saving Data over Long Periods of Time
Data can be saved to the SL1000’s internal acquisition memory over long durations, or it can also be streamed in real-time to a PC's hard disk or the SL1000’s internal hard disk ¹ ².
¹: with the /HD1 Option
²: Maximum speed of real time hard disk recording depends on measuring conditions.
³: Trigger mode: Single, measuring on 1 module, 2 channels.
Supports parallel testing
Perform measurements with up to four simultaneously independent sample rates. The amount of data saved on hard disk can be reduced by optimizing the sample rate for the DUT on a module by module basis.
High-Speed Data Transfer & GIGAZoom Function
You can transfer data to the PC at high speeds via USB 2.0 or Ethernet 1000BASE-T Gigabit Ethernet¹. The SL1000’s high-speed data compression engine (GIGAZoom engine) displays waveforms on the PC in real time² (even with massive amounts of data at high sample rates). It offers the same display updating and zooming performance as standalone measuring instruments.
¹: with the /C10 Option
²: The number of channels from which waveforms can be displayed during measurement may be limited depending on the PC performance and measuring conditions.
Real Time Saving to Hard Disk
Continuously measured data can be saved in real time to a PC's hard disk and/or the SL1000's internal hard disk ¹. File names are assigned automatically, freeing you from time consuming file operations. Data can be saved simultaneously - and in real time - to both the PC’s and SL1000's hard disks ¹. This bolsters the reliability of your data storage system, protecting your vital data. You can access the SL1000's internal hard disk ¹ with Xviewer waveform viewer software, or through an FTP client over Ethernet ².
¹: with the /HD1 Option
²: with the /C10 Option
³: Typical values. Actual values depend on PC performance and measurement conditions.
Settings for the Hard Disk Recording Function
By using the various recording features, you can efficiently and automatically record only the data you need to the hard disk. Just specify the recording destination, recording start and stop conditions, conditions for repeating recording, and other criteria. With free run mode, the specifiable parameters for the recording start condition are immediate, time, and alarm; for the recording stop condition, the parameters are continuous, time, recording time, and alarm; and for the repeating condition, recording interval and number of recordings*. With triggered mode, measured data is recorded on each trigger. You can also manually save data from the SL1000's internal acquisition memory to PC hard disk.
*: Max. file size per recording is 12 GB (recording on 4 channels, approximately 1.5 GW/ch)
Multi Units Synchronization
Maximum 8 Synchronized Units
- 100 MS/s up to 128 ch (16ch x 8 units)
- Can use 4 different sample rates across all units
- (Supports Parallel testing)
- Can combine trigger and alarm for channels across all units
- Maximum speed for saving in real time1
- PC HDD: 1.6 MS/s = 100kS/s x 16ch > 10kS/s x 128ch (Total data transfer rate to PC HDD is 1.6MS/s) Unit HDD: 1.6MS/s = 100kS/s x 16ch (100kS/s x 128ch with 8 units)
1: Typical values. Actual values depend on PC performance and measurement conditions
(Note)
In synchronized unit mode, recording into PC and SL1000 embedded HDD at the same time is not possible.
The recording file is per unit basis. (Utility software interface.)
Acquisition Software
Setting Marks
You can input the comments in the mark area when monitoring (Free run mode) over long periods of time.
Real time X-Y Display
You can now see both the T-Y and X-Y waveform Display. It is easy to evaluate data with fast update.
Auto Play
It is easy to set zoom position of waveform when measuring over long periods of time data or large data.
File Utility Function
You can save the data in both ASCII and Binary format. You can also load data with the same analysis program (ex. MATLAB).
Setting Operation Display
Accumulating Waveforms
You can easily detect unevenness or changes in acquired data.
Setup Wizard Makes It Easy
The Wizard automatically recognizes any connected SL1000 and its' plug-in modules. Just click the Start button to start measuring right away - no complicated settings to enter. The four screens of the Setup Wizard guide you easily through detailed settings for configuring the system, measuring, saving and displaying. Of course, you can save and recall your settings at any time.
Individual Sample Rates for Each Measurement Channel Group
Up to four groups of measurement channels can be defined with individual measurement conditions and display settings. Even waveforms from groups with different sample rates can be displayed in the same window.
Easy Tabular Setup Screens
Measurement conditions and channel display settings can be viewed and set easily using a tabular format. Use drag and drop shortcuts to quickly setup multiple channels.
Measurement condition setting screen Display setting screen
Control Buttons - Just Like Your DVD Remote
Measurement and saving can be started and stopped using the same familiar buttons found on a DVD remote control. Start using the instrument on the same day you receive it, with absolutely no programming required.
Real Time Waveform Display and Analysis
You can display a zoomed portion of the waveform simultaneously with the overall waveform during triggered measurement. Even during live recording, you can use the display hold * to review past data. You can also perform cursor measurements or automated measurement of waveform parameters (up to 26 during triggered measurement) in real time.
*: The display hold may automatically switch to display resume depending on the measuring conditions.
Easy Display Setup
Adjust your vertical display scale with ease using mouse shortcuts.
File Transfer
Adjust your vertical display scale with ease using mouse shortcuts.The File Transfer Function transfers files from the SL1000 to PC via, the Acquisition Software, intelligently in the case of multiple synchronized units.
File Utility *
SL1000 File Utility is file processing software for manipulating acquired files before analyzing waveforms with Xviewer. It can also analyze multiple channels across several units at the same time.
* SL1000 File Utility is bundled with the SL1000 standard install CD.
Xviewer / XviewerLITE
Xviewer is a PC software application designed to work with Yokogawa’s digital oscilloscopes and ScopeCorders.
MATLAB WDF Access Toolbox
MATLAB WDF Access Toolbox enables the access to waveform data files saved in WDF format on MATLAB.
To control the instruments on MATLAB, please use Instrument Control Toolbox provided by MathWorks.
- Released new firmware version 2.40
720211 High-Speed 100 M/s, 12-Bit Isolation Module
High-Speed 100 MS/s 12-Bit Isolation Module (2 channels)
IsoPRO technology enables 1kV isolated measurements in combination with 700929 or 701947 probe and is designed for inverter / IGBT related applications in mind. Using high speed optical fiber-based transmission, the module achieves high speed ADC clock and data isolation and provides the performance needed to develop high efficiency inverters, which employ high voltages, large currents, and ever increasing switching speeds.
Applicable to DL350, DL850 series, DL950 and SL1000.
720250 Voltage Module 10MS/s
- 720250 Voltage Module
- 10 MS/s sample rate
- 12-bit resolution
- 3 MHz bandwidth
- 2 isolated channels
- DL350, DL850, DL950, SL1000
720281 Frequency Module
- 720281 Frequency Module
- 1 MS/s sample rate 16-bit resolution
- 2 isolated channels
- 420 V*2, 42 V*3 max input voltage
- ±0.1% DC accuracy
- 0.01 Hz to 500 kHz measurement frequency
701947 Isolated Probe 1000V / 200 MHz
- 1.5m Isolated Probe (ScopeCorder)
- DC to 200 MHz bandwidth
- 100:1 attenuation Isolated
- BNC connector type
- For ScopeCorder Isolated Modules
702902 Isolated Passive Probe 1000V / 60 MHz
Passive Probe, 1000V(DC+ACpeak) CAT II, 60MHz, 10:1, 10MΩ, 2.5m
Wide operating temperature range(-40 to 85°C)
For isolated BNC input modules for ScopeCoder series
701251 Analog Voltage Input Module
- 701251 Analog Input Module
- High-Speed 1 Ms/s 16-Bit Isolation Module (2 ch)
- High sensitivity range (10 mV), low noise (±100 µVtyp), high noise immunity
- DL850, DL750, SL1000
700929 Isolated Passive Probe 1000V / 100 MHz
- Versatile 700929 passive oscilloscope probe
- 100MHz frequency bandwidth
- Isolated input module of ScopeCorder series
- For use with isolated BNC inputs
701940 Passive Probe 600V / 10 MHz
- 701940 Passive Probe
- 10 MHz, 10:1/1:1, 600 V (DC + ACpeak) CAT II, 1.5 m
- For ScopeCorder Non-Isolated Modules
701255 Analog Voltage Input Module
High-Speed 10 MS/s 12-Bit non-isolation Module (2 ch)
Non-Isolation version of model 720250
Applicable to DL350, DL850 series, DL950 and SL1000.
701977 Differential Probe 7000 V / 50 MHz
- 701977 Differential Probe for Oscilloscope 7000 V / 50 MHz
- 50 MHz, 1000:1 / 100:1, Max.
- Differential Voltage: 5000 Vrms and 7000 Vpeak or less
701978 Differential Probe 1500 V / 150 MHz
- 701978 Differential Probe for Oscilloscope
- 1500 V / 150 MHz
- 500:1 / 50:1
- Max. Differential Voltage：±1500 V (DC + ACpeak)
720268 High Voltage Module 1MS/s
- 720268 High Voltage Power Supply Module
- 300 kHz bandwidth
- 2 isolated channels
- Max input (DC+ACpeak) 1000V
- DC accuracy ±0.25%,
- DL350, DL850, DL950, SL1000
701917 Current Probe 50 MHz / 5 ARMS
- 701917 oscilloscope current probe
- Frequency bandwidth: DC to 50 MHz
- Maximum continuous input range: 5 Arms
- Functions with Digital Oscilloscopes, ScopeCorders, other waveform measuring instruments
701918 Current Probe 120 MHz / 5 ARMS
- Yokogawa 701918 Current Probe
- Frequency bandwidth: DC to 120 MHz
- Maximum continuous input range: 5 Arms
- Functions with Digital Oscilloscopes, ScopeCorders, other waveform measuring instruments
701930 Current Probe 10 MHz / 150 ARMS
- 701930 Current Probe 10 MHz / 150 ARMS
- Powered by Yokogawa Digital Oscilloscopes, Scopecorders or external power supply
701261 Universal Voltage & Temperature Input Module
- 701261 Universal Module (2 ch)
- Thermocouple (K, E, J, T, L, U, N, R, S, B, W, iron-doped gold/chromel)
- Applicable to DL350, DL850 series, DL950 and SL1000.
701931 Current Probe 2 MHz / 500 ARMS
- 701931 Current Probe 2 MHz / 500 ARMS
- Powered by Yokogawa Digital Oscilloscopes, Scopecorders or external power supply
701262 Universal Voltage & Temperature Input Module (w/AAF)
- Universal Module (with Anti-Aliasing Filter, 2 ch)
- Thermocouple (K, E, J, T, L, U, N, R, S, B, W, iron-doped gold/chromel), with AAF
- DL350, DL850 series, DL950 and SL1000
701932 Current Probe 100 MHz / 30 ARMS
- 701932 Current Probe 100 MHz / 30 ARMS
- Powered by Yokogawa Digital Oscilloscopes, Scopecorders, or external power supply
701933 Current Probe 50 MHz / 30 ARMS
- 701933 50 by 30 current probe
- Powered by Yokogawa Digital Oscilloscopes, Scopecorders or external power supply
701265 High-Precision Temperature Input Module
Temperature/high-precision voltage Module (2 ch)
Thermocouple (K, E, J, T, L, U, N, R, S, B, W, iron-doped gold/chromel), high sensitivity range (1 mV), and low noise (±4 µVtyp)
Applicable to DL350, DL850 series, DL950 and SL1000.
701934 External Probe Power Supply
- 701934 External Probe Power Supply
- Power supply for current probes, FET probes, and differential probes
- Supplies power for up to four probes, including large current probes
720266 High-Sensitivity, Low-Noise, Voltage, Temperature Module
- The 720266 Temperature Module/Voltage Module
- 16-Bit, 125 S/s (Voltage) and 125 S/s (Temperature) sample rate
- DL350, DL850 series, DL950, SL1000
701270 Strain Input Module (NDIS)
- Strain Module, NDIS (2 channels)
- 701955 or 701956 NDIS bridge head
- Detect/display mechanical stress with ScopeCorder
- DL350, DL850 series, DL950, SL1000
701271 Strain Input Module (DSUB)
Strain Module with Shunt Calibration, type DSUB (2 channels) to be used in combination with 701957 or 701958 DSUB bridge head.
Using the strain module and strain gauge the ScopeCorder can detect and display mechanical stress (strain). It works on the principle that the resistance value of a metal foil changes as it expands and contracts.
Applicable to DL350, DL850 series, DL950 and SL1000.
A1002JC NDIS Connector for 701270
- Yokogawa Oscilloscope and ScopeCorder products
- A1002JC NDIS connector
- Direct connection to strain module 701270
701955/701956 NDIS Bridge Heads 120Ω/350Ω
- ScopeCorder Accessories for DL850 series, DL750/DL750P, SL1000 & SL1400
- 701955 NDIS Bridge Head, Bridge resistance: 120Ω , 5m NDIS cable included
- 701956 NDIS Bridge Head, Bridge resistance: 350Ω , 5m NDIS cable included
701275 Acceleration & Voltage Input Module (w/AAF)
- 2 channel Voltage Module/Acceleration Module
- Anti-Aliasing Filter
- Direct input from built-in amp type acceleration sensor to measure acceleration
- DL350, DL850 series, DL950 and SL1000.
701957/701958 D-Sub Bridge Heads 120Ω/350Ω
- 701957 and 701958 D-SUB Bridge Head
- Shunt calibration
- 5m DSUB cable included
- Bridge resistance: 120Ω
- Bridge resistance: 350Ω
366923 BNC to T Adapter
T-adapter for BNC connectors. Use for circuits having voltage levels no greater than 42 V.
751512 Banana (Male) to Binding Post Adapter
Safety-terminal-binding-post adapter. Use for circuits having voltage levels no greater than 42 V.
758924 BNC to Banana Conversion Adapter
For conversion between BNC and female banana plug
Applicable for DL750/DL750P, SL1000 & SL1400.
B8099NM 4mm conversion adapter
For 702902, 702906
758917 DMM Measurement Lead Set
- Set of 0.8m long red and black multimeter test leads
- Used in combination with a pair of optional 758922 or 758929 alligator-clip adapters
- 1000 Vrms, 32 Arms CAT II
758933 Measurement lead
2 pieces (red and black) in 1 set
length: 1.00 m
Used in combination with the 701959, 758921, 758922, or 758929
Rating: 1000 V CAT III/19 A
701901 BNC to Safety Banana 1.8m Cable, 1:1
- 701901 BNC to Safety Banana 1.8m Cable, 1:1
- 1000 Vrms-CAT II, 1.8 m long
- Safety BNC(male) to safety banana(female)
- 701959, 701954, 758921, 758922, 758929
701906 Long Test Clip
Set contains one black and one red clip
1000 Vrms-CAT II
2 pieces (red and black) in 1 set
Connected to the 758933, 758917, or 701901
Length: 0.3m
Applicable for DL750/DL750P, SL1000, SL1400
701948 Extension Clip Accessories
Connected to the 700929, 701947
Maximum input voltage: 1,000V (DC + ACpeak)
Length: 0.26m/0.3m/0.4m
Applicable for DL750/DL750P, SL1000, SL1400
701954 Large Alligator Clip (dolphin type)
Set contains one black and one red clip.
1000 Vrms-CAT II.
720930 Clamp on Probe
The 720930 and 720931 passive clamp-on current probes allow current waveform readings directly via analog input modules on ScopeCorders including the DL350 and DL850 using isolated BNC connections.
- AC 50 A
- 40 Hz to 3.5 kHz Bandwidth
758929 Large Alligator Clip Adapter 1000V
- Yokogawa 758929 Alligator Clip Adapter
- Rated at 1000V
- Attaches to 758917 test leads
- Sold in pairs black/red
758922 Small Alligator-Clip Adapter 300V
Rated at 300 V. Attaches to the 758917 test leads. Sold in pairs.
720931 Clamp on Probe
The 720931 passive clamp-on current probe anables current waveform readings directly via analog input modules on ScopeCorders including the DL350 and DL850 using isolated BNC connections.
- AC 200 A
- 40 Hz to 3.5 kHz Bandwidth
758921 Fork terminal adapter
- 758921 Fork Terminal Adapters
- For fitting a 4mm banana plug to a fork terminal
- One black and one red clip
- 1000 Vrms-CAT II
758931 Screw-Fastened Safety Voltage Terminal Adapter Set
Screw-fastened adapters. Two adapters in a set. 1.5 mm Allen Wrench.
701902/701903 Safety BNC to BNC Cable 1m/2m
- 701902/701903 Safety BNC to BNC Cable for oscilloscope
- Safe, high-voltage measurements with DL350, DL950, and SL1000 isolated input modules
- 701902: 1000 Vtms-CAT II (BNC-BNC), 1 m
- 701903: 1000 Vrms-CAT II (BNC-BNC), 2 m
366924 BNC to BNC 1m Cable
- 366924 BNC to BNC cable for oscilloscope
- 1m BNC wire
- Simultaneous measurement with 2 units
- Input external trigger signal
366925 BNC to BNC 2m Cable
BNC-BNC 2m. For connection to simultaneously measurement with 2 units, or for input external trigger signal.
366926 BNC to Alligator 1m Cable, 1:1
- 1 m long BNC to alligator clip cable
- Only for circuits with voltage levels no greater than 42 V
- Applicable for DL750/DL750P, SL1000 & SL1400
366961 Banana to Alligator 1.2m Cable, 1:1
A subassembly of 1.2 m long test leads with alligator-clip adapters.
Use only for circuits having voltage levels no greater than 42 V.
Applicable for SL1000 & SL1400.
701919 Probe Stand
- 701919 oscilloscope probe stand
- Flexible arm, heavy base to hold and stabilize 8-13mm probes
- Can simplify circuit board testing
751541-E4 Rack mount kit
For SL1000 (EIA)
751541-J4 Rack mount kit
For SL1000 (JIS)
758928 Pinchers tip (Hook type)
1000 Vrms CAT III, 1 set each of red and black
Equivalent to B9852MM (Color Black)
Equivalent to B9852NM (Color Red)
Observation of Inverter Switching Waveforms
There are several factors for a user to consider when using an IEPE accelerometer, particularly when used with newly available integrated signal conditioner/data acquisition process. Correctly managing these factors will help the user avoid erroneous data from their IEPE accelerometer and ensure the quality of the data measurement is at the level they expect and require.
Surge Waveform Recording & Power Monitoring
With increased focus on reducing energy consumption and compliance with efficiency standards, this app note provides an overview on the types of measurements needed for efficiency and power quality, and the instruments that take them.
The objective of this paper is to show the close relationship between efficiency and power quality, and provide education on the causes of power quality, types of power quality issues, and provide guidance on measurement considerations.
Xviewer may only be used to view and analyze data saved by the SL1000, it cannot be used to remotely control the SL1000. You can also transfer files between the SL1000 and a PC. For the SL1000, Xviewer can support ...
- Update Firmware on SL1000 High Channel Count ScopeCorder modular data acquisition system
- Follow instruction procedures
- "Beat Method" for Inspecting an Oscilloscope’s Time Base Accuracy
- Inspect and verify time base accuracy
- Aliasing effect to create a "beat waveform."
- Time base setting formula
- Xviewer can open multiple files from different DL, SL, and WE series instruments into a single window display
- Same sample rate, trigger position, record length
Please see the attached document.
- DC Precision when changing the DC waveform position setting on DL1600
- How to calculate DC offset voltage
Even though the correct USB drivers have been installed, and the device displays correctly in the Windows Device Manager Window, the High-Speed Data Acquisition Unit SL1000 Acquisition Software fails to detect the SL1000 main unit. Solutions: Verify ...
Yes, you can use the 700929 isolated probe with non-isolated input modules.
The SL1000 High-Speed Data Acquisition Unit is capable of linking up to 8 units, up to 128ch max, in synchronized mode using our SL1000 Acquisition Software. Using a common LINK file, data from all units can be processed and analyzed, as one, at the ...
One possible solution is to use a third party 10:1 attenuator such as the one shown in the attached document. You may use the attenuator to allow the direct input of higher voltage levels with the 701262 module, since ...
The AC Power Input in all Yokogawa instruments is designed as a 3-pin connection (one of which is a GND pin). In some parts of the world, PCs are sold with AC power cables that are 2-pin. Often times this means the ...
The SL1000 High-Speed Data Acquisition Unit Portable Parallel Analyzer (PPA) doesn’t support offset summing like DLM2000 Mixed Signal Oscilloscopes. The SL1000 doesn't have offset hardware; instead, the vOffset variable is used to affect the displayed value only. So, using this parameter would have no ...
High Resolution mode can be used to remove high frequency noise and increase vertical resolution. It achieves this by increasing the number of effective bits per data to 12-bits through digital and bandwidth filters.
- Correct AC coupling test for the 720210 Analog Voltage input module must be performed at 20 Hz
- Service manual SMDL850-01EN_010 1st Ed suggests performing AC COUPLING test at 15 Hz
- This is a typo
The sanitation procedure for various Yokogawa oscilloscopes have been documented below. Please download the document or pdf that refers to your Yokogawa oscilloscope.
No, the SL1000 and 720210 Modules service manual does not include any adjustment procedures however, it does contain the inspection procedure (QIS).
To perform a shunt calibration using the 701271 strain gage module and the ScopeCorder, please complete the following procedures: Connect the strain module 701271, bridge head 701957/701958 and the strain ...
The SL1000 High-Speed Data Acquisition Unit has the following types of memory: Internal Hard Drive: 40 GB Non-Volatile SRAM Waveform Acquisition Memory: 128 MW or 256 MB Volatile RAM Setup File Data Storage: 1 MB Volatile SRAM(Battery-Backup)
The maximum total file size you can record continuously depends on your sample rate, channel count and storage capacity. Please see the attached PDF file for an example of recording settings.Note: The dead-time between ...
The SL1000 is capable of transferring previous data sets/files while streaming is still in progress through the File Divide feature. When the SL1000 starts recording, it opens a new file and starts logging data. If the ...
Yes, VXI-11 is required and needs to be enabled for the DLM2000 Mixed Signal Oscilloscope to connect properly to Xviewer when using an ethernet connection. If the VXI-11 option is unchecked, a connection failed message will appear. Related ...
There are some modules that can be used with the DL750 Scopecorder but cannot be used with the DL850 Scopecorder. This is due to the nature of the FPGA for that module, which cannot be interchanged between the DL750 Scopecorder and the DL850 Scopecorder. During ...
Depending on the mode, the dead time may range from 0 to 10ms approximately. The dead time for the different modes are listed below. Free Run Mode: 0ms Normal Mode without HDD recording: 10ms Normal Mode with HDD ...
This training module covers the following topics:
- Introduction & Installation
- Basics of Xviewer
- Advanced features
- Video Demonstrations
Brochures
- SL1000 High-Speed Data Acquisition Unit (7.4 MB)
- Data Acquisition Unit SL1000/Acquisition SoftwareV2.10(with Change Sheet RS01-7201-20V21E-01) (370 KB)
- Plug-in modules specifications ScopeCorder series DL950/DL850E/DL850EV/DL350/SL1000 (4.0 MB)
- Probes and accessories for Oscilloscopes (2.2 MB)
Instruction Manuals
- Precaution Concerning the Modules (178 KB)
- SL1000 High-Speed Data Acquisition Unit (7.1 MB)
- SL1000 Input Module (682 KB)
- SL1000 Acquisition Software (10.8 MB)
- SL1000 Acquisition Software Version Upgrade Procedure(Only for Web) (314 KB)
- SL1000 Data Acquisition Unit Firmware Version Upgrade Procedure(Only for Web) (195 KB)
- SL1000 Control API Use's Manual (954 KB)
- SL1000 High-Speed Data Acquisition Unit Communication Interface User's Manual (1.0 MB)
- Read before Installing the Software (SL1000 Control API) (420 KB)
- Combustion Pressure Analysis Software (For Gasoline) (1.8 MB)
- Combustion Pressure Analysis Software (For Diesel) (2.0 MB)
- Combustion Pressure Analysis Software (For Gas) (1.9 MB)
- Please Read before Installation (Combustion Pressure Analysis Software) (756 KB)
Specifications
- SL1000 EPICS driver specifications (280 KB)
Software
- Xviewer 701992 / XviewerLITE
- MATLAB WDF Access Toolbox
- DL-Term
- Binary Data File Converter
- Yokogawa WDF DataPlugin ( NATIONAL INSTRUMENTS Web Page )
- USB Drivers
- TMCTL
- SL1000 High-Speed Data Acquisition Unit (Software/Firmware Bundle)
- LabVIEW Drivers for SL1000 ( NATIONAL INSTRUMENTS Web Page )
Drawings
Webinars
- How to avoid the “gotcha's” of inverter-based measurements
- Computations for field-oriented control
- The integration of CAN bus communications
- Correlations in the frequency domain
- Other advanced motor and drive topics
You know the basics of electrical power measurements, have set up your dyno, and made key measurements – which is great. But as your motor and drive projects progress, the complexities of system drive requirements can change frequently. Control algorithms, networked communications, and mechanical systems form a complex web of interactions that need sorting. This 60-minute webinar explains how to get past ground-level measurements and delve into comprehensive solutions that leverage test and measurement instruments including power analyzers, high-speed data acquisition, and real-time software.
Topics include:
The technical presentation includes an audience Q&A.