KNOWLEDGEBASE
(54) Results were found. Showing 31-40.
Why Can't I use the Waveform Parameter Measure Function or the Computation Math Function for the WE7000 Series?
To use the waveform parameter Measure function or the computation Math function, you need the 707702 Computation Function Setup Software. In the case of the WE7111, you can perform waveform parameter automatic measuremen...
item: 1166 | http://tmi.yokogawa.com/kr/service-support/faqs/1166/
Is There an Arbitrary Waveform Data Creation Tool for Output on the WE7281 and WE7121 Module?
Yes, there is a software called the 707751 Arbitrary Waveform Editor. You can create waveforms using the editor's standard functions or with the mouse. You can read in files created in CSV, or in Yokogawa's proprietary ...
item: 1164 | http://tmi.yokogawa.com/kr/service-support/faqs/1164/
Can I set the Input Range for Each Channel on the A/D Modules?
Yes, you can set the range for each channel....
item: 1142 | http://tmi.yokogawa.com/kr/service-support/faqs/1142/
Can I use a 100Base-TX Ethernet Connection With the WE7000 Series?
Yes, you can use a 100Base-TX/10Base-T with the WE7052 Fast Ethernet Module....
item: 1153 | http://tmi.yokogawa.com/kr/service-support/faqs/1153/
Is There an Alternative Solution to Using a 10:1 Probe for Higher Voltage Input?
One possible solution is to use a third party 10:1 attenuator such as the one shown in the attached document. You may use the attenuator to allow the direct input of higher voltage levels with the 701262 module, since it...
item: 239 | http://tmi.yokogawa.com/kr/service-support/faqs/239/
I Want to Connect the Ethernet Module to a LAN, Does it Support DHCP?
Yes, the WE7052 Fast Ethernet module supports DHCP. However, you must have the WE7000 control software ver. 4 or later. ...
item: 1155 | http://tmi.yokogawa.com/kr/service-support/faqs/1155/
How can I Express an Arbitrary Exponentiation Other Than the Square and Cube Computation Function in XViewer?
You can express any arbitrary exponentiation, in Xviewer or DL series instruments, by using the LOG (common logarithm) and EXP (exponential) functions. For example, for C1 raised to the exponent of 0.2, the math functio...
item: 575 | http://tmi.yokogawa.com/kr/service-support/faqs/575/
Is There an Input Filter on the Digitizer Modules?
The WE7275 2-CH, 1 MS/s isolated digitizer module comes with an up-to-40 kHz anti-aliasing filter. Also, each digitizer module (WE7275/WE7271/WE7272/WE7251/WE7245) includes a low-pass filter. The cut-off frequency varies...
item: 1146 | http://tmi.yokogawa.com/kr/service-support/faqs/1146/
WE7000 Series Module Become Unresponsive When the Main Power Switch of the Measuring Station is Turned OFF and Then Immediately ON Again
You must wait at least five seconds after turning the power switch to the measuring instrument OFF before turning it back ON again. If you wait less than five seconds, there is a possibility for a malfunction to occur in...
item: 1172 | http://tmi.yokogawa.com/kr/service-support/faqs/1172/
Can I Make a Direct One-to-One Connection From the PC to the Measuring Station Using a Cross Cable?
Connection made by a cross cable does not comply with Ethernet standards. For reliable data communications, please use a hub when you want to make a direct connection to a PC. ...
item: 1158 | http://tmi.yokogawa.com/kr/service-support/faqs/1158/
