Harmonic Analysis Software For WT1000/WT2000 series

Description

WT1000 Series: perform harmonic analasis conforming to the IEC1000-3-2 standard. This software does not have the capability to distinguish the class (based on the IEC standard) of the item being measured by the level of the higher harmonics. However, you can enter the WT1000/WT2000's voltage and current range settings, and change the display in the instrument's front panel. panel
panel panel


WT2000 Series: perform harmonic analasis conforming to the IEC1000-3-2 standard.
Allows you to perform hours of continuous measurement, 16 cycles at a time, and make evaluations at 2.5 minute intervals. In particular, you can simultaneously measure 3 phases, and this provides even more uses for the instrument. The general functions of this software allow you to enter the voltage and current range, and other settings in the instrument's display panel.
panel panel
 

Applicable Model

WT1030M, WT1010, WT1030, WT2010, WT2030
 

System Requirements

PCA PC with a 80486DX2 CPU or later (Pentium or later recommended), and 8 MB or more of memory.

Operating system: Windows 98, Windows Me, Windows 2000 Professional, or Windows XP
Floppy disk drive: 3.5" floppy disk drive using 1.44 MB (MS-DOS compatible) type disks
Hard disk: A hard disk drive with 10 MB of available free space
Video adapter: A video adapter capable of displaying at 640 x 480 or higher resolution (1024 x 768, 16 bit color or higher recommended)
Display: VGA and Windows compatible display capable of displaying 256 colors (RGB) or more
Printer: Any device compatible with Windows
Mouse: Any device compatible with Windows
Communications interface: GP-IB: a GP-IB adapter by National Instruments (AT-GPIB, AT-GPIB/TNT, or PCMCIA-GPIB)
RS-232: a built-in port, or COM1 or COM2 exclusive (COM1 only for PC9801 or PC9821)
 

Connecting the WT Series Instrument to a PC

GP-IB Interface to prevent electric shock, turn the power to the instrument OFF when connecting it to the PC. Connect a GP-IB cable from the GP-IB connector on the rear panel of the WT series instrument to the corresponding connector on the PC.

  • Setting the Address
    Set the GP-IB address according to the procedure given in the user's manual that came with the WT series instrument. For details about the GP-IB interface, refer to the information about the communications functions included in the user's manual.
  • RS-232C Interface
    To prevent electric shock, turn the power to the PC OFF when connecting the instrument to it. Connect an RS-232 cable from the RS-232 connector on the rear panel of the WT series instrument to the serial port of the PC.
  • Parameter settings
    Follow the procedure given in the user's manual of the WT series instrument to enter the following parameter settings. (Normally, operation can begin using the factory default settings.)
    Handshaking: select a method from 0 to 7.
    Data format: select a format from 0 to 3.
    Baud rate: select 75, 150, 300, 600, 1200, 2400, 4800, or 9600.
    Terminator: select CR+LF, CR, or LF.
    For details about the RS-232 interface, refer to the user's manual that came with the WT series instrument.
 

Installation

Turn on your PC and start Windows.
Extract the downloaded ZIP compressed file. A new folder, same as the file name (WTx000hrm), will be created on drive C and files will be extracted to it.
If so, installation is complete.

Creating Icons for the WT Free Software

After the program has been installed, you can use Explorer to create a shortcut to the program. Locate the executable file, right-click its icon, and select Create Shortcut from the shortcut menu.

Running the Software

Double-click the program executable file or its shortcut to run the software.

 

Download

 

Please read Software Agreement carefully before downloading.

 

Release Date Apr 22, 2019
File Name wtx000hrm.zip 1.2 MB

  

Type Software

 

* Softwarevereinbarung
  • Die Schutzrechte, Eigentumsrechte, Rechte an geistigem Eigentum und alle anderen mit der Software verbundenen Rechte werden von der Yokogawa Test & Measurement Corporation gehalten.
  • Unter keinen Umständen ist ein Dumping, Dekompilierung, umgekehrter Aufbau, Rückwärtsentwicklung oder jede andere Art von Änderung oder Revision dieser Software erlaubt.
  • Diese Software wird kostenlos angeboten, aber es werden keine unbegrenzten Garantien gegen jegliche Mängel gemacht.
  • Auch ist Yokogawa nicht in der Lage, Anfragen zur Reparatur von Mängeln oder Fragen zu dieser Software zu akzeptieren.
  • Der Inhalt dieser Software kann ohne vorherige Ankündigung geändert werden, da die Software und die Funktionen der Software weiter verbessert werden.
  • Yokogawa haftet nicht für Probleme, die während des Downloads oder der Installation dieser Software auftreten können.
  • Die Nutzung der Yokogawa-Website erfolgt auf eigene Gefahr.
  • Alle Parteien, die zur Erstellung oder Verbreitung der Inhalte auf der Yokogawa-Website beitragen, haften nicht für Schäden, die durch die Verwendung dieser Inhalte entstehen.

Das Herunterladen der Software zeigt die Zustimmung zu der Softwarevereinbarung .

Related Products & Solutions

WT2010/WT2030 Digitale Leistungsmessgeräte

Die digitalen Leistungsmessgeräte der Serie WT2000 wurden im Hinblick auf ein optimales Preis/Leistungsverhältnis (Bandbreite, Genauigkeit, Messgeschwindigkeit und Störunterdrückung) entwickelt. Durch den großen Funktionsumfang lassen sich diese Messgeräte in unterschiedlichen Anwendungsbereichen einsetzen.

 
Oben