GermanyDE  

Digitale Leistungsanalysatoren

Anwendungssoftware für Leistungsmessungen

Die Applikationssoftware von Yokogawa zeichnet sich durch eine hohe Leistung und Flexibilität aus und kann dadurch Ihre Anwendungen beschleunigen. Dieses sehr leistungsfähige Softwarewerkzeug eignet sich sowohl für numerische Messdaten, als auch für Signal- und Oberwellendaten. Es ermöglicht eine Übertragung der Daten auf einen Personal Computer und bietet somit eine maximale Flexibilität und Unterstützung.

  • WTViewerE Application Software für WT3000E/ WT3000/ WT1800E/ WT1800/ WT500/ WT300E/ WT300 (761941)

    Mit der WTViewerE Software können Yokogawa Leistungsanalysatoren, wie der WT3000E, WT1800E, WT500 und WT300E, über eine Ethernet-, USB-, GPIB- oder RS232-Schnittstelle mit einem PC verbunden werden. Über diese Verbindung kann der Anwender aus der Ferne Messungen steuern und überwachen sowie Messdaten sammeln, analysieren und speichern.

    WTViewerE Application Software für WT3000E/ WT3000/ WT1800E/ WT1800/ WT500/ WT300E/ WT300 (761941) thumbnail

  • WTViewerFreePlus für WT300/WT300E Serie (KOSTENLOS)

    Die WTViewerFreePlus Software kann gemessene numerische Werte, harmonische Werte und Signal-Daten erfassen. Die Daten können über eine USB-, GP-IB/RS-232- oder Ethernet-Schnittstelle auf einen PC übertragen und dort dargestellt sowie gespeichert werden.
    Folgende 11 Sprachen werden unterstützt:
      Englisch, Japanisch, Chinesisch vereinfacht, Chinesisch traditionell,
      Deutsch, Italienisch, Koreanisch, Russisch, Spanisch, Thai und Indonesisch

    WTViewerFreePlus für WT300/WT300E Serie (KOSTENLOS) thumbnail

  • Software zur IEC 62301 Ed.2.0 konformen Leistungsmessung

    Das neue Softwarepaket bildet zusammen mit den Yokogawa Leistungs­analysatoren eine komplette Lösung zur normgerechten Bestimmung der Ruheverluste gemäß IEC62301 Ed.2.0 (international) und EN50564:2011 (europäisch).

    Software zur IEC 62301 Ed.2.0 konformen Leistungsmessung thumbnail

  • WTViewerEfree für WT5000/WT3000E/WT3000/WT1800E/ WT1800/WT500/ WT300E/WT300 (kostenlos)

    WTViewerEfree ist eine kostenlose Software für die Präzisions-Leistungsanalysatoren WT5000/WT3000E/WT3000/WT1800E/WT1800/ WT500/WT300E/WT300. Dieses Software-Tool erlaubt eine einfache & schnelle Bedienung der Messgeräte und eine problemlose Erfassung der Messwerte mit einem PC. Dem Anwender steht damit eine leistungsfähige und hilfreiche Messumgebung zur Verfügung.

    WTViewerEfree für WT5000/WT3000E/WT3000/WT1800E/ WT1800/WT500/ WT300E/WT300 (kostenlos) thumbnail

  • WTViewer für WT3000/WT1800/WT500 (760122)

    Mit dem Software-Werkzeug WTViewer lassen sich numerische, Signal- und Oberschwingungs-Daten aus den digitalen Leistungsmessgeräten WT3000/WT1800/WT500 auslesen.

    WTViewer für WT3000/WT1800/WT500 (760122) thumbnail

  • PowerViewerPlus (760881)

    Mit der PowerViewerPlus Software (760881) für den PX8000 lassen sich gemessene Signale und numerische Daten auf einen PC (Personal Computer) zu weiteren Berechnungen und Analysen übertragen.

    PowerViewerPlus (760881) thumbnail

  • WTViewer für WT210/WT230

    Einfache Erfassung und Bearbeitung von Leistungsmessdaten mit einem PC 

    WTViewer für WT210/WT230 thumbnail

  • Datenlogging-Software GA10

    Die neue Software ermöglicht die Realisierung von Datenerfassungssystemen ohne Programmierung. Die GA10 Software wurde im Hinblick auf eine maximale Kompatibilität mit Recordern, Datenloggern, Temperaturreglern und Leistungsmonitoren von Yokogawa entwickelt und kann auch Daten über Modbus erfassen.

    Datenlogging-Software GA10 thumbnail

  • Oberschwingungs-/Flicker-Analysesoftware für WT3000/WT2000/WT1600 (761922)

    761922 Oberschwingungs-/Flicker-Mess-Software gemäß einschlägigen IEC Normen

    Oberschwingungs-/Flicker-Analysesoftware für WT3000/WT2000/WT1600 (761922) thumbnail
White Papers & Fachartikel
How Accurate Are Your Power Measurements?
Thumbnail
366 KB
T&M Hausmagazin
Yokogawa T&M Hausmagazin 50/18
Thumbnail
690 KB
Overview:
  • Reportage
    - Warum Format keine Frage der Größe ist
  • Neuheiten
    - Präzisions Leistungsanalysator - WT5000
    - Mixed-Signal-Oszilloskop - DLM3000
  • Hintergrund
    - Effizienz als Grundstein des Erfolgs
FAQ
Can Xviewer.exe be run as multiple instance?
Thumbnail
Overview:
Can Xviewer.exe be run as multiple instance?   No - not at this time. Xviewer can not control two or more DL850 chassis. Xviewer can not connect to two or more instruments at the same time. Two or more Xviewer ...
FAQ
Complete List of Windows 7 Compatible Yokogawa Software
Thumbnail
Overview:
The following softwares have been tested for Windows 7 compatibility. WTViewer Xviewer SL1000 Acquisition Software USB Instrument Drivers for all USB supported instruments TMCTL Library Files for programming with VB, ...
FAQ
WTViewerFree Causes a Lack of Memory Error During Data Saving in CSV Format
Thumbnail
Overview:
When using WTViewerFree to automatically save data in CSV format, a lack of memory may occur due to increasing load on anti-virus software such as Virus Buster. As the data save time becomes longer, the CSV file will ...
FAQ
How can I Programatically Retrieve All 500 Harmonic Order Measurements on the WT1800 / WT1800E?
Thumbnail
Overview:

To programmatically read all 500 harmonic orders measurement values, please use the ":NUMERIC:LIST" command set. The maximum number of items for the :NUMERIC:LIST:VALUE? command is 64.  However, 1 LIST ITEM can ...
FAQ
Is There a Way to Lock Out All the Keys, Including LOCAL, on the WT210/WT230?
Thumbnail
Overview:
It is possible to lock out all the keys, including LOCAL, on the WT210/WT230 using a GPIB specific or controller specific command.For the GPIB controller from National Instruments, the command is called LLO or Local ...
FAQ
Which Bits in the Extended Event Register Corresponds to the “Check Range” LED Indicator on the WT210/WT230?
Thumbnail
Overview:
If you want to know the condition of the "Check Range" LED indicator for voltage and current, you will need to read three bits in the Extended Event Register. "Bit-6", "Bit-7", and "Bit-8" needs to be read to know the ...
FAQ
Is WTViewer Supported Under the Linux Environment?
Thumbnail
Overview:
Although WTViewer is not officially supported under the Linux environment, users have successfully done so using WINE (flavor of Linux) via RS232. For connectivity to WT210/WT230, WTViewer requires that the meter be set ...
FAQ
What is the Difference Between the DL/DLM Series IEC Harmonic Measurement and the WT3000 IEC Harmonic Measurement via the Harmonic Analysis Software?
Thumbnail
Overview:
The IEC Harmonic analysis on the DL/DLM series oscilloscopes provides a rough analysis and estimation for harmonic testing. The scope will perform an FFT on the current waveform and can be used to measure the general ...
FAQ
What driver should I use when connecting WT500/WT1800 via USB from NI LabVIEW Environment?
Thumbnail
Overview:
To use USB interface on the WT500 and WT1800 from NI LabVIEW environment, you will need to use the USB driver from National Instruments. This USB driver is usually installed when you install NI-VISA and is called the ...
FAQ
Why Doesn't WTViewer Communicate with my WT Series Power Meter via GPIB?
Thumbnail
Overview:
There are several items you will need to check and verify to solve this issue. Verify the GP-IB connectionSome instruments have a D/A output connector located next to the GP-IB connector. There have been some ...
FAQ
How do I Analyze the Waveform Data Saved From the PZ4000?
Thumbnail
Overview:
You can use the Power Viewer (Model 253734) software. However if you only need to view waveforms, we recommend you use the Waveform Viewer (Model 700919, version 1.23 or later) software. The trial version of the Power ...
FAQ
How Do I Resolve the "LACK" Measurement Reading in DAQLOGGER When Connected to the WT230 via GateWT?
Thumbnail
Overview:

When making a WT230 RS232C connection using GateWT, please verify the following RS232C communication settings on the instrument: Mode = 488.2 Hand = 0 For = 0 Baud Rate = 9600 Terminator Cr+Lf Even though you can run ...
FAQ
How do I Programmatically Read Average Active Power Right Before the End of the Integration Interval While in Continuous Integration for the WT230?
Thumbnail
Overview:
You can read the average active power during continuous integration mode (just before the integral resets) for the WT230, by monitoring the status of the ITG or ITM bits of the extended event register.   Bit 1 ITG is ...
FAQ
Will DL Term Work with the WT1800?
Thumbnail
Overview:
Yes, you can use DL Term with the WT1800 using an Ethernet (VXI-11) or USB connection.
FAQ
Why Can't I See the Harmonic Bar Graph in WTViewer After a Single Update When Connected to the WT1600?
Thumbnail
Overview:
For the WT1600, to view the harmonic data in the Bar Graph window of WTViewer, you have to select all the harmonic orders in the Numeric window. WTViewer's Bar Graph window display follows the harmonic items activated ...
FAQ
Why Can't I Save the WT Settings for the WT500, WT1800, or WT3000 When Using WTViewer?
Thumbnail
Overview:
The WTViewer Save Setting feature will only save the setting information of the WTViewer. The Save Setting feature will NOT save the setting information of the instrument. The saved file for the WT500, WT1800 or ...
FAQ
Is There a Way to Lock Out All the Keys, Including LOCAL, on the WT210/WT230?
Thumbnail
Overview:
It is possible to lock out all the keys, including LOCAL, on the WT210/WT230 using a GPIB specific or controller specific command.For the GPIB controller from National Instruments, the command is called LLO or Local ...
FAQ
Which Bits in the Extended Event Register Corresponds to the “Check Range” LED Indicator on the WT210/WT230?
Thumbnail
Overview:
If you want to know the condition of the "Check Range" LED indicator for voltage and current, you will need to read three bits in the Extended Event Register. "Bit-6", "Bit-7", and "Bit-8" needs to be read to know the ...
FAQ
How do I Analyze the Waveform Data Saved From the PZ4000?
Thumbnail
Overview:
You can use the Power Viewer (Model 253734) software. However if you only need to view waveforms, we recommend you use the Waveform Viewer (Model 700919, version 1.23 or later) software. The trial version of the Power ...
FAQ
How can I Programatically Retrieve All 500 Harmonic Order Measurements on the WT1800 / WT1800E?
Thumbnail
Overview:

To programmatically read all 500 harmonic orders measurement values, please use the ":NUMERIC:LIST" command set. The maximum number of items for the :NUMERIC:LIST:VALUE? command is 64.  However, 1 LIST ITEM can ...
FAQ
What driver should I use when connecting WT500/WT1800 via USB from NI LabVIEW Environment?
Thumbnail
Overview:
To use USB interface on the WT500 and WT1800 from NI LabVIEW environment, you will need to use the USB driver from National Instruments. This USB driver is usually installed when you install NI-VISA and is called the ...
FAQ
Is WTViewer Supported Under the Linux Environment?
Thumbnail
Overview:
Although WTViewer is not officially supported under the Linux environment, users have successfully done so using WINE (flavor of Linux) via RS232. For connectivity to WT210/WT230, WTViewer requires that the meter be set ...
FAQ
Will DL Term Work with the WT1800?
Thumbnail
Overview:
Yes, you can use DL Term with the WT1800 using an Ethernet (VXI-11) or USB connection.
FAQ
What is the Difference Between the DL/DLM Series IEC Harmonic Measurement and the WT3000 IEC Harmonic Measurement via the Harmonic Analysis Software?
Thumbnail
Overview:
The IEC Harmonic analysis on the DL/DLM series oscilloscopes provides a rough analysis and estimation for harmonic testing. The scope will perform an FFT on the current waveform and can be used to measure the general ...
FAQ
Why Doesn't WTViewer Communicate with my WT Series Power Meter via GPIB?
Thumbnail
Overview:
There are several items you will need to check and verify to solve this issue. Verify the GP-IB connectionSome instruments have a D/A output connector located next to the GP-IB connector. There have been some ...
FAQ
Why Can't I Save the WT Settings for the WT500, WT1800, or WT3000 When Using WTViewer?
Thumbnail
Overview:
The WTViewer Save Setting feature will only save the setting information of the WTViewer. The Save Setting feature will NOT save the setting information of the instrument. The saved file for the WT500, WT1800 or ...
FAQ
How Do I Resolve the "LACK" Measurement Reading in DAQLOGGER When Connected to the WT230 via GateWT?
Thumbnail
Overview:

When making a WT230 RS232C connection using GateWT, please verify the following RS232C communication settings on the instrument: Mode = 488.2 Hand = 0 For = 0 Baud Rate = 9600 Terminator Cr+Lf Even though you can run ...
FAQ
Why Can't I See the Harmonic Bar Graph in WTViewer After a Single Update When Connected to the WT1600?
Thumbnail
Overview:
For the WT1600, to view the harmonic data in the Bar Graph window of WTViewer, you have to select all the harmonic orders in the Numeric window. WTViewer's Bar Graph window display follows the harmonic items activated ...
FAQ
How do I Programmatically Read Average Active Power Right Before the End of the Integration Interval While in Continuous Integration for the WT230?
Thumbnail
Overview:
You can read the average active power during continuous integration mode (just before the integral resets) for the WT230, by monitoring the status of the ITG or ITM bits of the extended event register.   Bit 1 ITG is ...
eBook
Download eBook: Electricity Applied - A handbook of common applications and key measurement parameters
Thumbnail
Branchen:
Vorgestellt Technical Article
Infographic: Getting started with electrical power measurements
Thumbnail
Overview:

Energy efficiency directives from bodies like International Electro technical Commission (IEC), European commission, California Energy Commission (CEC) and others govern standards across various classes of electrical, electronic and mechatronic equipment.

This infographic provides a snapshot guide for making reliable power measurements across your product development lifecycle with particular emphasis on the high accuracy needs of compliance testing. 

Branchen:

How-tos

Suchen Sie mehr Informationen über unsere Mitarbeiter, Technologie oder Lösungen?


Ihr Kontakt zu uns
 
Oben